AT32UC3A0512AU Atmel Corporation, AT32UC3A0512AU Datasheet - Page 440

• Manufacturer Part Number: AT32UC3A0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 109
• Ext Interrupts: 109
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
29.5.1.2
Table 29-1.
Bit
31:2
31
30
29
28
27
26
25
24
23
22
21
1
0
Address of beginning of buffer
Wrap - marks last descriptor in receive buffer descriptor list.
Ownership - needs to be zero for the MACB to write data to the receive buffer. The MACB sets this to one once it has
successfully written a frame to memory.
Software has to clear this bit before the buffer can be used again.
Global all ones broadcast address detected
Multicast hash match
Unicast hash match
External address match
Reserved for future use
Specific address register 1 match
Specific address register 2 match
Specific address register 3 match
Specific address register 4 match
Type ID match
VLAN tag detected (i.e., type id of 0x8100)
Receive Buffers
Receive Buffer Descriptor Entry
Thus the bus latency must be less than the time it takes to load the FIFO and transmit or receive
three words (12 bytes) of data.
At 100 Mbit/s, it takes 960 ns to transmit or receive 12 bytes of data. In addition, six master clock
cycles should be allowed for data to be loaded from the bus and to propagate through the
FIFOs. For a 60 MHz master clock this takes 100 ns, making the bus latency requirement 860
ns.
Received frames, optionally including CRC/FCS, are written to receive buffers stored in mem-
ory. Each receive buffer is 128 bytes long. The start location for each receive buffer is stored in
memory in a list of receive buffer descriptors at a location pointed to by the receive buffer queue
pointer register. The receive buffer start location is a word address. For the first buffer of a
frame, the start location can be offset by up to three bytes depending on the value written to bits
14 and 15 of the network configuration register. If the start location of the buffer is offset the
available length of the first buffer of a frame is reduced by the corresponding number of bytes.
Each list entry consists of two words, the first being the address of the receive buffer and the
second being the receive status. If the length of a receive frame exceeds the buffer length, the
status word for the used buffer is written with zeroes except for the “start of frame” bit and the
offset bits, if appropriate. Bit zero of the address field is written to one to show the buffer has
been used. The receive buffer manager then reads the location of the next receive buffer and
fills that with receive frame data. The final buffer descriptor status word contains the complete
frame status. Refer to
Table 29-1
Word 0
Word 1
for details of the receive buffer descriptor list.
Function
AT32UC3A
440