AT32UC3A0512AU Atmel Corporation, AT32UC3A0512AU Datasheet - Page 505

• Manufacturer Part Number: AT32UC3A0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 109
• Ext Interrupts: 109
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
30.7.1.4
30.7.1.4.1
30.7.1.4.2
30.7.1.4.3
30.7.1.4.4
30.7.1.4.5
MCU Power Modes
Run Mode
Idle Mode
Frozen Mode
Standby, Stop, DeepStop and Static Modes
USB Clock Frozen
See
device and host interrupts.
There are two kinds of general interrupts: processing, i.e. their generation is part of the normal
processing, and exception, i.e. errors (not related to CPU exceptions).
The processing general interrupts are:
The exception general interrupts are:
In this mode, all MCU clocks can run, including the USB clock.
In this mode, the CPU is halted, i.e. the CPU clock is stopped. The Idle mode is entered what-
ever the state of the USB macro. The MCU wakes up on any USB interrupt.
Same as the Idle mode, except that the HSB module is stopped, so the USB DMA, which is an
HSB master, can not be used. Moreover, the USB DMA must be stopped before entering this
sleep mode in order to avoid erratic behavior. The MCU wakes up on any USB interrupt.
Same as the Frozen mode, except that the USB generic clock and other clocks are stopped, so
the USB macro is frozen.
In the Run, Idle and Frozen MCU modes, the USB macro can be frozen when the usb line is in
the suspend mode, by setting the FRZCLK bit, what reduces power consumption.
In this case, it is still possible to access the following elements, but only in Run mode:
Moreover, when FRZCLK is set, only the asynchronous interrupt sources may trigger the USB
interrupt:
•the ID Transition interrupt (IDTI);
•the VBus Transition interrupt (VBUSTI);
•the SRP interrupt (SRPI);
•the Role Exchange interrupt (ROLEEXI).
•the VBus Error interrupt (VBERRI);
•the B-Connection Error interrupt (BCERRI);
•the HNP Error interrupt (HNPERRI);
•the Suspend Time-Out interrupt (STOI).
•the OTGPADE, VBUSPO, FRZCLK, USBE, UIDE, UIMOD and LS bits;
•the DPRAM (through the USB_FIFOX_DATA registers, but not through USB bus transfers
•the ID Transition interrupt (IDTI);
which are frozen).
Section 30.7.2.17 on page 520
and
Section 30.7.3.13 on page 528
for further details about
AT32UC3A
505