AT86RF212 Atmel Corporation, AT86RF212 Datasheet - Page 50
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT86RF212
Manufacturer Part Number
AT86RF212
Description
Manufacturer
Atmel Corporation
Specifications of AT86RF212
Max. Operating Frequency
0 MHz
Crypto Engine
AES
Operating Voltage (vcc)
1.8 to 3.6
Frequency Band
700/800/900MHz
Max Data Rate (mb/s)
1
Antenna Diversity
No
External Pa Control
Yes
Power Output (dbm)
10
Receiver Sensitivity (dbm)
-110
Receive Current Consumption (ma)
9.0
Transmit Current Consumption (ma)
18 at 5dBm
Link Budget (dbm)
120
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT86RF212-ZU
Manufacturer:
HITTITE
Quantity:
5 000
Part Number:
AT86RF212-ZU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT86RF212-ZUR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT86RF212B-ZU
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
50
AT86RF212
Table 5-10. Configuration of a PAN Coordinator
Promiscuous Mode or Sniffer
The promiscuous mode is described in IEEE 802.15.4-2006, section 7.5.6.5. This mode
is further illustrated in Figure 5-9. According to IEEE 802.15.4-2006, in promiscuous
mode the MAC sub layer shall pass received frames with correct FCS to the next higher
layer without further processing. This implies that received frames should never be
automatically acknowledged.
In order to support sniffer application and promiscuous mode, only second level filter
rules as defined by IEEE 802.15.4-2006, section 7.5.6.2, are applied to the received
frame.
Table 5-11 shows the RX_AACK configuration registers required to setup a typical
IEEE 802.15.4 compliant device which operates in promiscuous mode.
0x20,0x21
0x22,0x23
Register
Address
0x0C
0x2C
0x2B
0x2E
0x2E
0x2E
0x24
…
Register
7:6
Bit
7
0
3
5
Name
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
…
IEEE_ADDR_7
RX_SAFE_MODE
SLOTTED_OPERATION
AACK_I_AM_COORD
AACK_SET_PD
AACK_FVN_MODE
Description
Setup Frame Filter, see section 6.2.1
0: Disable frame protection
1: Enable frame protection
0: Transceiver operates in unslotted
mode.
1: Transceiver operates in slotted mode,
see section 5.2.3.5.
1: Device is PAN coordinator
0: “Frame Pending” subfield is 0 in FCF
1: “Frame Pending” subfield is 1 in FCF
Controls the ACK behavior, depending on
FCF frame version number
b00: Acknowledges only frames with
version number 0, i.e. according to
IEEE 802.15.4-2003 frames
b01: Acknowledges only frames with
version number 0 or 1, i.e. frames
according to IEEE 802.15.4-2003/2006
b10: Acknowledges only frames with
version number 0 or 1 or 2
b11: Acknowledges all frames,
independent of the FCF frame version
number
8168C-MCU Wireless-02/10