ATmega165P Atmel Corporation, ATmega165P Datasheet - Page 267

• Manufacturer Part Number: ATmega165P
• Manufacturer: Atmel Corporation

Specifications of ATmega165P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.2
8019K–AVR–11/10
Fuse Bits
Table 25-2.
Notes:
The ATmega165P has three Fuse bytes.
the functionality of all the fuses and how they are mapped into the Fuse bytes. Note that the
fuses are read as logical zero, “0”, if they are programmed.
Table 25-3.
Notes:
–
–
–
–
BODLEVEL2
BODLEVEL1
BODLEVEL0
RSTDISBL
Fuse Low Byte
BLB1 Mode
1
2
3
4
1. Program the Fuse bits and Boot Lock bits before programming the LB1 and LB2.
2. “1” means unprogrammed, “0” means programmed.
1. See
2. Port G, PG5 is input only. Pull-up is always on.
Memory Lock Bits
(2)
77.
(1)
(1)
(1)
Lock Bit Protection Modes
Extended Fuse Byte
Table 26-5 on page 302
BLB12
1
1
0
0
Bit No
7
6
5
4
3
2
1
0
BLB11
–
–
–
–
Brown-out Detector trigger level
Brown-out Detector trigger level
Brown-out Detector trigger level
External Reset Disable
Description
1
0
0
1
Protection Type
No restrictions for SPM or LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and LPM
executing from the Application section is not allowed to read
from the Boot Loader section. If Interrupt Vectors are placed in
the Application section, interrupts are disabled while executing
from the Boot Loader section.
LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
for BODLEVEL Fuse decoding.
(1)(2)
Table 25-3
(Continued)
to
See “Alternate Functions of Port G” on page
Table 25-5 on page 268
Default Value
1
1
1
1
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
ATmega165P
describe briefly
267