ATtiny85 Atmel Corporation, ATtiny85 Datasheet - Page 133

• Manufacturer Part Number: ATtiny85
• Manufacturer: Atmel Corporation

Specifications of ATtiny85

• Flash (kbytes): 8 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 3
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 5
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

17.8
2586N–AVR–04/11
Analog Input Circuitry
Noise Reduction and Idle mode. To make use of this feature, the following procedure should be
used:
Note that the ADC will not be automatically turned off when entering other sleep modes than Idle
mode and ADC Noise Reduction mode. The user is advised to write zero to ADEN before enter-
ing such sleep modes to avoid excessive power consumption.
The analog input circuitry for single ended channels is illustrated in Figure 17-8. An analog
source applied to ADCn is subjected to the pin capacitance and input leakage of that pin, regard-
less of whether that channel is selected as input for the ADC. When the channel is selected, the
source must drive the S/H capacitor through the series resistance (combined resistance in the
input path).
Figure 17-8. Analog Input Circuitry
The ADC is optimized for analog signals with an output impedance of approximately 10 kΩ or
less. If such a source is used, the sampling time will be negligible. If a source with higher imped-
ance is used, the sampling time will depend on how long time the source needs to charge the
S/H capacitor, with can vary widely. The user is recommended to only use low impedant sources
with slowly varying signals, since this minimizes the required charge transfer to the S/H
capacitor.
Signal components higher than the Nyquist frequency (f
distortion from unpredictable signal convolution. The user is advised to remove high frequency
components with a low-pass filter before applying the signals as inputs to the ADC.
• Make sure that the ADC is enabled and is not busy converting. Single Conversion mode must
• Enter ADC Noise Reduction mode (or Idle mode). The ADC will start a conversion once the
• If no other interrupts occur before the ADC conversion completes, the ADC interrupt will wake
be selected and the ADC conversion complete interrupt must be enabled.
CPU has been halted.
up the CPU and execute the ADC Conversion Complete interrupt routine. If another interrupt
wakes up the CPU before the ADC conversion is complete, that interrupt will be executed,
and an ADC Conversion Complete interrupt request will be generated when the ADC
conversion completes. The CPU will remain in active mode until a new sleep command is
executed.
ADCn
I
IH
I
IL
1..100 kΩ
ADC
/2) should not be present to avoid
C
ATtiny25/45/85
S/H
= 14 pF
V
CC
/2
133