SAM9G46 Atmel Corporation, SAM9G46 Datasheet - Page 51

• Manufacturer Part Number: SAM9G46
• Manufacturer: Atmel Corporation

Specifications of SAM9G46

• Flash (kbytes): 0 Kbytes
• Pin Count: 324
• Max. Operating Frequency: 400 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 160
• Ext Interrupts: 160
• Usb Transceiver: 3
• Usb Speed: Hi-Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 2
• Uart: 5
• Lin: 4
• Ssc: 2
• Ethernet: 1
• Sd / Emmc: 2
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: Yes
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 440
• Resistive Touch Screen: Yes
• Temp. Sensor: No
• Crypto Engine: AES/DES
• Sram (kbytes): 64
• Self Program Memory: NO
• External Bus Interface: 2
• Dram Memory: DDR2/LPDDR, SDRAM/LPSDR
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 0.9 to 1.1
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

10.12 Touch Screen Analog-to-Digital Converter (TSADC)
10.13 Ethernet 10/100 MAC (EMAC)
10.14 Image Sensor Interface (ISI)
11028CS–ATARM–20-Apr-11
• 8-channel ADC
• Support 4-wire resistive Touch Screen
• 10-bit 384 Ksamples/sec. Successive Approximation Register ADC
• -3/+3 LSB Integral Non Linearity, -2/+2 LSB Differential Non Linearity
• Integrated 8-to-1 multiplexer, offering eight independent 3.3V analog inputs
• External voltage reference for better accuracy on low voltage inputs
• Individual enable and disable of each channel
• Multiple trigger sources
• Sleep Mode and conversion sequencer
• Compatibility with IEEE
• 10 and 100 Mbits per second data throughput capability
• Full- and half-duplex operations
• MII or RMII interface to the physical layer
• Register Interface to address, data, status and control registers
• DMA Interface, operating as a master on the Memory Controller
• Interrupt generation to signal receive and transmit completion
• 128-byte transmit and 128-byte receive FIFOs
• Automatic pad and CRC generation on transmitted frames
• Address checking logic to recognize four 48-bit addresses
• Supports promiscuous mode where all valid frames are copied to memory
• Supports physical layer management through MDIO interface
• Supports Wake On Lan. The receiver supports Wake on LAN by detecting the following
• ITU-R BT. 601/656 8-bit mode external interface support
• Support for ITU-R BT.656-4 SAV and EAV synchronization
• Vertical and horizontal resolutions up to 2048 x 2048
• Preview Path up to 640*480
• Support for packed data formatting for YCbCr 4:2:2 formats
events on incoming receive frames:
– Hardware or software trigger
– External trigger pin
– Automatic wakeup on trigger and back to sleep mode after conversions of all
– Magic packet
– ARP request to the device IP address
– Specific address 1 filter match
– Multicast hash filter match
enabled channels
®
Standard 802.3
SAM9G46
51