AD7193 Analog Devices, AD7193 Datasheet - Page 51
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7193
Manufacturer Part Number
AD7193
Description
4-Channel, 4.8 kHz, Ultralow Noise, 24-Bit Sigma-Delta ADC with PGA
Manufacturer
Analog Devices
Datasheet
1.AD7193.pdf
(56 pages)
Specifications of AD7193
Resolution (bits)
24bit
# Chan
4
Sample Rate
n/a
Interface
Ser,SPI
Analog Input Type
Diff-Uni,SE-Uni,Usr-Defined Range/Offset
Ain Range
± (Vref/Gain)
Adc Architecture
Sigma-Delta
Pkg Type
SOP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD7193BRUZ
Manufacturer:
ADI
Quantity:
1 000
Part Number:
AD7193BRUZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7193BRUZ-REEL
Manufacturer:
ADI
Quantity:
1 000
Part Number:
AD7193BRUZ-REEL
Manufacturer:
ADI原装
Quantity:
20 000
Company:
Part Number:
AD7193BRUZ-SMD
Manufacturer:
TI
Quantity:
5 600
Data Sheet
Figure 65 shows the filter response when FS[9:0] is set to 5 and
the post filter averages by 16. In this case, the output data rate is
equal to 53.33 Hz when the first filter notch is placed at 60 Hz.
The rejection at 60 Hz ± 0.5 Hz is equal to 40 dB minimum.
Simultaneous 50 Hz/60 Hz rejection is achieved when FS[9:0] is
set to 30 and the postfilter averages by 16. The output data rate
is equal to 8.9 Hz whereas the rejection at 50 Hz ± 0.5 Hz and
60 Hz ± 0.5 Hz is typically 42 dB.
–100
–120
–100
–120
–110
–110
–10
–20
–30
–40
–50
–60
–70
–80
–90
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
0
Figure 65. Filter Response for Average + Decimate Filter
Figure 66. Filter Response for Average + Decimate Filter
0
0
(Sinc
(Sinc
30
30
3
3
Filter, FS[9:0] = 30, Average by 16)
Filter, FS[9:0] = 5, Average by 16)
FREQUENCY (Hz)
FREQUENCY (Hz)
60
60
90
90
120
120
150
150
Rev. C | Page 51 of 56
Simultaneous 50 Hz and 60 Hz rejection is also achieved by using
an FS word of 96 and averaging by 16, which places a notch at
50 Hz. Setting the REJ60 bit to 1 places a notch at 60 Hz (see
Figure 67). The output data rate is reduced to 2.78 Hz with this
configuration, but the rejection is improved to 94 dB typically at
50 Hz ± 1 Hz and 60 Hz ± 1 Hz.
FAST SETTLING MODE (CHOP ENABLED)
Chop can be enabled in the fast settling mode. With chop
enabled, the ADC offset and offset drift are minimized. The
analog input pins are continuously swapped. With the analog
input pins connected in one direction, the settling time of the
sinc filter is allowed and a conversion is recorded. The analog
input pins are then inverted, and another settled conversion is
obtained. Subsequent conversions are averaged so that the offset
is minimized. This continuous swapping of the analog input
pins and the averaging of subsequent conversions means that
the offset drift is also minimized.
Chopping does not change the output data rate. However, the
settling time equals
Consequently, if chop is enabled, the sinc
is set to 6, averaging by 16 is enabled, and the output data rate is
equal to 42.1 Hz. Therefore, the conversion time equals 1/42.10 Hz
or 23.75 ms, and the settling time is equal to 47.5 ms.
t
SETTLE
–100
–110
–120
–10
–20
–30
–40
–50
–60
–70
–80
–90
0
Figure 67. Filter Response for Average + Decimate Filter
0
= 2/f
(Sinc
ADC
3
30
Filter, FS[9:0] = 96, Average by 16)
FREQUENCY (Hz)
60
90
4
filter is selected, FS[9:0]
120
AD7193
150