AD7699 Analog Devices, AD7699 Datasheet - Page 7

• Manufacturer Part Number: AD7699
• Description: 16-Bit, 8-Channel, 500 kSPS PulSAR ADC
• Manufacturer: Analog Devices

Specifications of AD7699

• Resolution (bits): 16bit
• # Chan: 8
• Sample Rate: 500kSPS
• Interface: Ser,SPI
• Analog Input Type: Diff-Uni,SE-Bip,SE-Uni
• Ain Range: (Vref) p-p,4 V p-p,Bip (Vref) x 0.5,Uni (Vref)
• Adc Architecture: SAR
• Pkg Type: CSP

Data Sheet
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 5. Pin Function Descriptions
Pin No.
1, 20
2
3
4, 5
6 to 9
10
11
12
13
14
15
16 to 19
21 (EPAD)
1
AI = analog input, AI/O = analog input/output, DI = digital input, DO = digital output, and P = power.
Mnemonic
VDD
REF
REFIN
GND
IN4 to IN7
COM
CNV
DIN
SCK
SDO
VIO
IN0 to IN3
Exposed
Paddle
(EPAD)
Type
P
AI/O
AI/O
P
AI
AI
DI
DI
DI
DO
P
AI
1
Description
Power Supply. Nominally 4.5 to 5.5 V and should be decoupled with 10 μF and 100 nF capacitors.
Reference Input/Output. See the Voltage Reference Output/Input section.
When the internal reference is enabled, this pin produces 4.096 V. When the internal reference is disabled
and the buffer is enabled, REF produces a buffered version of the voltage present on the REFIN pin
(VDD – 0.5 V maximum) useful when using low cost, low power references.
For improved drift performance, connect a precision reference to REF (0.5 V to VDD).
For any reference method, this pin needs decoupling with an external 10 μF capacitor connected as
close to REF as possible. See the Reference Decoupling section.
Internal Reference Output/Reference Buffer Input. See the Voltage Reference Output/Input section.
When using the internal reference, the internal unbuffered reference voltage is present and needs
decoupling with a 0.1 μF capacitor.
When using the internal reference buffer, apply a source between 0.5 V and 4.096 V that is buffered to
the REF pin as previously described.
Power Supply Ground.
Analog Input Channel 4, Analog Input Channel 5, Analog Input Channel 6, and Analog Input Channel 7.
Common Channel Input. All input channels, IN[7:0], can be referenced to a common-mode point of 0 V
or V
Conversion Input. On the rising edge, CNV initiates the conversion. During conversion, if CNV is held
high, the busy indictor is enabled.
Data Input. This input is used for writing to the 14-bit configuration register. The configuration register
can be written to during and after conversion.
Serial Data Clock Input. This input is used to clock out the data on SDO and clock in data on DIN in an
MSB first fashion.
Serial Data Output. The conversion result is output on this pin and synchronized to SCK. In unipolar
modes, conversion results are straight binary; in bipolar modes, conversion results are twos
complement.
Input/Output Interface Digital Power. Nominally at the same supply as the host interface (1.8 V, 2.5 V,
3 V, or 5 V).
Analog Input Channel 0, Analog Input Channel 1, Analog Input Channel 2, and Analog Input Channel 3.
The exposed paddle is not connected internally. For increased reliability of the solder joints, it is
recommended that the pad be soldered to the GND plane.
REF
/2 V.
NOTES
1. THE EXPOSED PADDLE IS NOT CONNECTED INTERNALLY.
FOR INCREASED RELIABILITY OF THE SOLDER JOINTS,
IT IS RECOMMENDED THAT THE PAD BE SOLDERED TO
THE GND PLANE.
REFIN
GND
GND
VDD
REF
Figure 4. Pin Configuration
1
2
3
4
5
Rev. A | Page 7 of 28
(Not to Scale)
AD7699
TOP VIEW
PIN 1
INDICATOR
15 VIO
14 SDO
13 SCK
12 DIN
11 CNV
AD7699