STM8S007C8 STMicroelectronics, STM8S007C8 Datasheet - Page 45

• Manufacturer Part Number: STM8S007C8
• Description: Value line, 24 MHz STM8S 8-bit MCU, 64 Kbytes Flash, true data EEPROM
• Manufacturer: STMicroelectronics

Specifications of STM8S007C8

• Max Fcpu: up to 24 MHz, 0 wait states @ fCPU≤ 16 MHz
• Program: 64 Kbytes Flash; data retention 20 years at 55 °C after 100 cycles
• Data: 128 bytes true data EEPROM; endurance 100 kcycles
• Ram: 6 Kbytes
• Advanced Control Timer: 16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization

STM8S007C8
Table 14.
1. Data based on characterization results, not tested in production.
2. All power (V
3. I/O pins used simultaneously for high current source/sink must be uniformly spaced around the package
4. I
5. Negative injection disturbs the analog performance of the device. See note in
6. When several inputs are submitted to a current injection, the maximum
Table 15.
I
ΣI
INJ(PIN)
external supply.
between the V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
there is no positive injection current, and the corresponding V
characteristics on page
positive and negative injected currents (instantaneous values). These results are based on
characterization with
INJ(PIN)
Symbol
INJ(PIN)
Symbol
I
I
ΣI
VDD
VSS
I
T
IO
IO
STG
T
(4)(5)
J
must never be exceeded. This is implicitly insured if V
(4)
Current characteristics
Thermal characteristics
DD
DDIO
, V
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Total output current sourced (sum of all I/O and control pins)
for devices with two V
Total output current sourced (sum of all I/O and control pins)
for devices with one V
Total output current sunk (sum of all I/O and control pins) for
devices with two V
Total output current sunk (sum of all I/O and control pins) for
devices with one V
Injected current on NRST pin
Injected current on OSCIN pin
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DDIO
/V
SSIO
Σ
, V
I
INJ(PIN)
IN
76.
DDA
>V
pins.
DD
) and ground (V
Maximum junction temperature
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Storage temperature range
Doc ID 022171 Rev 2
SSIO
DD
SSIO
SS
DDIO
power lines (source)
DDIO
Ratings
pins
ground lines (sink)
pin
SS
Ratings
, V
(3)
pins
pin
(3)
SSIO
(3)
(3)
(6)
, V
SSA
) pins must always be connected to the
IN
IN
maximum must always be respected
maximum is respected. If V
(2)
(2)
Σ
I
IN
INJ(PIN)
<V
INJ(PIN)
(6)
Electrical characteristics
SS
Section 9.3.10: 10-bit ADC
. For true open-drain pads,
is the absolute sum of the
-65 to 150
value. A positive
Value
150
Max.
±20
200
100
160
60
60
20
20
80
±4
±4
±4
IN
(1)
maximum
Unit
Unit
°C
mA
45/90