ST72361J6 STMicroelectronics, ST72361J6 Datasheet - Page 179

• Manufacturer Part Number: ST72361J6
• Description: 8-bit MCU
• Manufacturer: STMicroelectronics

Specifications of ST72361J6

• Hdflash Endurance: 100 cycles, data retention 40 years at 85°C
• 5 Power Saving Modes: Halt, Auto Wake Up From Halt, Active Halt, Wait and Slow

12.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
12.2.1 Voltage Characteristics
12.2.2 Current Characteristics
12.2.3 Thermal Characteristics
Notes:
1. Directly connecting the RESET and I/O pins to V
is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter).
To guarantee safe operation, this connection has to be done through a pull-up or pull-down resistor (typical: 4.7kΩ for
RESET, 10kΩ for I/Os). Unused I/O pins must be tied in the same way to V
2. I
respected, the injection current must be limited externally to the I
while a negative injection is induced by V
corresponding V
3. All power (V
4. Negative injection disturbs the analog performance of the device. See note in
page
5. When several inputs are submitted to a current injection, the maximum ΣI
and negative injected currents (instantaneous values). These results are based on characterization with ΣI
mum current injection on four I/O port pins of the device.
|ΔV
INJ(PIN)
204.
DDx
|V
I
V
ΣI
V
V
INJ(PIN)
V
SSA
Symbol
Symbol
Symbol
ESD(HBM)
DD
PP
INJ(PIN)
ESD(MM)
| and |ΔV
T
I
I
V
must never be exceeded. This is implicitly insured if V
VDD
VSS
I
STG
T
IO
- V
- V
- V
IN
J
2)4)
DD
SS
SS
SSx
2)
IN
) and ground (V
|
SSx
maximum must always be respected
|
Supply voltage
Programming Voltage
Input voltage on any pin
Variations between different digital power pins
Variations between digital and analog ground pins
Electro-static discharge voltage (Human Body Model)
Electro-static discharge voltage (Machine Model)
Total current into V
Total current out of V
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on V
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on PB3 (on Flash devices)
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
Storage temperature range
Maximum junction temperature (see
SS
) lines must always be connected to the external supply.
IN
< V
DD
SS
PP
SS
power lines (source)
. For true open-drain pads, there is no positive injection current, and the
Ratings
Ratings
Ratings
1)2)
pin
ground lines (sink)
DD
or V
5)
SS
could damage the device if an unintentional internal reset
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
Section 13.2 "THERMAL
INJ(PIN)
IN
maximum is respected. If V
3)
3)
value. A positive injection is induced by V
DD
INJ(PIN)
or V
5)
SS
“10-BIT ADC CHARACTERISTICS” on
according to their reset configuration.
see
is the absolute sum of the positive
V
SS
Maximum value
Maximum value
Section 12.8.3 on page 192
- 0.3 to V
CHARACTERISTICS")
-65 to +150
Value
± 25
150
- 25
± 5
± 5
6.5
13
50
50
25
50
+5
IN
maximum cannot be
DD
+ 0.3
INJ(PIN)
ST72361
Unit
Unit
Unit
179/225
mV
mA
IN
°C
V
>V
maxi-
DD