STE10-100A STMicroelectronics, STE10-100A Datasheet - Page 10
STE10-100A
Manufacturer Part Number
STE10-100A
Description
Pci 10/100 Ethernet Controller With Integrated Phy
Manufacturer
STMicroelectronics
Datasheet
1.STE10-100A.pdf
(82 pages)
- Current page: 10 of 82
- Download datasheet (795Kb)
Pin description
10/82
Table 1.
Physical interface
LED display & miscellaneous
107,109
105,104
Pin no.
101
98
97
90
92
Pin description (continued)
RX+, RX-
TX+, TX-
LED M1-
LED M2-
LED M1-
LED M2-
100 link
LK/Act
Speed
Name
Iref
Act
X1
X2
or
or
Type
O
O
O
O
O
I
I
25MHz reference clock input for physical portion. When an
external 25MHz crystal is used, this pin will be connected to
one of its terminals, and X2 will be connected to the other
terminal. If an external 25 MHz oscillator is used, then this
pin will be connected to the oscillator’s output pin.
25MHz reference clock output for physical portion. When an
external 25MHz crystal is used, this pin will be connected to
one of the crystal terminals (see X1, above). If an external
clock source is used, then this pin should be left open.
The differential transmit outputs of 100BASE-TX or 10BASE-
T, these pins connect directly to magnetic.
The differential receive inputs of 100BASE-TX or 10BASE-T,
these pins connect directly from magnetic.
Reference resistor connecting pin for reference current,
directly connects a 5KOhm ± 1% resistor to Vss.
This pin can be programmed as mode 1 or mode 2:
For mode 1:
LED display for link and activity status. This pin will be driven
on continually when a good Link test is detected. This pin will
be driven at a 10Hz blinking frequency when either effective
receiving or transmitting is detected.
For mode 2:
LED display for activity status. This pin will be driven at a
10Hz blinking frequency when either effective receiving or
transmitting is detected.
This pin can be programmed as mode 1 or mode 2:
For mode 1:
LED display for 100M b/s or 10M b/s speed. This pin will be
driven on continually when the 100M b/s network operating
speed is detected.
For mode 2:
LED display for 100Ms/s link status. This pin will be driven on
continually when 100Mb/s network operating speed is
detected.
Description
STE10/100A
Related parts for STE10-100A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools Eval Board for STE10
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10/100A - PCI 10/100 ETHERNET CONTROLLER WITH PHY DATASHEET
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A - PCI 10-100 ETHERNET CONTROLLER WITH PHY DATASHEET
Manufacturer:
STMicroelectronics
Part Number:
Description:
IC CTRLR PCI ETHERNET 128-PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
PCI10-100 ETHERNET CONTROLLER WITH INTEGRATED PHY (5V)
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A - PCI 10-100 ETHERNET CONTROLLER WITH PHY APPNOTE
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A EEPROM ACCESS AND PROGRAMMING
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet: