STE10-100A STMicroelectronics, STE10-100A Datasheet - Page 25
STE10-100A
Manufacturer Part Number
STE10-100A
Description
Pci 10/100 Ethernet Controller With Integrated Phy
Manufacturer
STMicroelectronics
Datasheet
1.STE10-100A.pdf
(82 pages)
- Current page: 25 of 82
- Download datasheet (795Kb)
STE10/100A
3.5.3
Flow control in full duplex application
The PAUSE function is used to inhibit transmission of data frames for a specified period of
time. The STE10/100A supports the full duplex protocol of IEEE802.3x. To support the
PAUSE function, the STE10/100A implements the MAC Control Sub-layer functions to
decode the MAC Control frames received from MAC control clients and to execute the
relative requests accordingly. When full duplex mode and the PAUSE function are selected
after Auto-Negotiation completes (refer to the configuration of XR8), the STE10/100A will
enable the PAUSE function for flow control in a full duplex application. In this section we will
describe how the STE10/100A implements the PAUSE function.
MAC control frame and PAUSE frame
Figure 14. MAC control frame format
The MAC control frame is distinguished from other MAC frames only by its length/type field
identifier. The MAC control opcode defined in MAC control frame format for the PAUSE
function is 0001h, and the PAUSE time is specified in the MAC control parameters field with
2 octets, representing an unsigned integer, in units of slot-times. The range of possible
PAUSE times is 0 to 65535 slot-times.
A valid PAUSE frame issued by a MAC control client (for example, a switch or a bridge)
would contain:
–
–
–
(min frame size – 160) / 8 octets
(min frame size – 160) / 8 octets
The destination address, set to the globally assigned 48 bit mulitcast address 01-
80-C2-00-00-01, or to the unicast address to which the MAC control client
requests to inhibit its transmission of data frames.
The MAC control opcode field set to 0001h.
2 octets of PAUSE time specified in the MAC control parameter field to indicate the
length of time for which the destination is requested to inhibit data frame
transmission.
6 octets
6 octets
6 octets
6 octets
2 octets
2 octets
2 octets
2 octets
Destination address
Destination address
Source address
Source address
Lenght/Type = 88-08h
Lenght/Type = 88-08h
MAC control Opcode
MAC control Opcode
MAC control parameter
MAC control parameter
Reserved (pads with zeroes)
Reserved (pads with zeroes)
Functional description
25/82
Related parts for STE10-100A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools Eval Board for STE10
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10/100A - PCI 10/100 ETHERNET CONTROLLER WITH PHY DATASHEET
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A - PCI 10-100 ETHERNET CONTROLLER WITH PHY DATASHEET
Manufacturer:
STMicroelectronics
Part Number:
Description:
IC CTRLR PCI ETHERNET 128-PQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
PCI10-100 ETHERNET CONTROLLER WITH INTEGRATED PHY (5V)
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A - PCI 10-100 ETHERNET CONTROLLER WITH PHY APPNOTE
Manufacturer:
STMicroelectronics
Part Number:
Description:
STE10-100A EEPROM ACCESS AND PROGRAMMING
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet: