SCA05010-BFN-LNN Shelly, Inc., SCA05010-BFN-LNN Datasheet - Page 23

• Manufacturer Part Number: SCA05010-BFN-LNN
• Description: Innovative Display Technologies 17171 Murphy Avenue
• Manufacturer: Shelly, Inc.

 PRECAUTIONS FOR USING LCD MODULES
Handing Precautions
chipped during handling especially on the edges. Please avoid dropping or jarring. Do not subject it to a
mechanical shock by dropping it or impact.
in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.
the color tone to vary. Do not touch the display with bare hands. This will stain the display area and
degraded insulation between terminals (some cosmetics are determined to the polarizer).
Handle this polarizer carefully. Do not touch, push or rub the exposed polarizer’s with anything harder
than an HB pencil lead (glass, tweezers, etc.). Do not put or attach anything on the display area to avoid
leaving marks on. Condensation on the surface and contact with terminals due to cold will damage, stain
or dirty the polarizer. After products are tested at low temperature they must be warmed up in a container
before coming is contacting with room temperature air.
dry cloth. If it is heavily contaminated, moisten cloth with one of the following solvents
Do not scrub hard to avoid damaging the display surface.
following.
Wipe off saliva or water drops immediately, contact with water over a long period of time may cause
deformation or color fading. Avoid contacting oil and fats.
by water droplets, moisture condensation or a current flow in a high-humidity environment.
sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I O cable
or the backlight cable.
attention should be paid to electrostatic discharge as for an ordinary CMOS IC. To prevent destruction of
the elements by static electricity, be careful to maintain an optimum work environment.
and your body have the same electric potential. Be sure to ground the body when handling the LCD
modules.
that for certain the AC power source for the soldering iron does not leak. When using an electric
screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as
possible any transmission of electromagnetic waves produced sparks coming from the communicator of
the motor.
work under dry conditions. To reduce the generation of static electricity be careful that the air in the work
is not too dried. A relative humidity of 50%-60% is recommended. As far as possible make the electric
potential of your work clothes and that of the work bench the ground potential
peeling off this protective film since static electricity may be generated
(1) The display panel is made of glass and polarizer. As glass is fragile. It tends to become or
(2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any
(3) Do not apply excessive force to the display surface or the adjoining areas since this may cause
(4) The polarizer covering the display surface of the LCD module is soft and easily scratched.
(5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft
(6) Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the
(7) Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated
(8) Install the LCD Module by using the mounting holes. When mounting the LCD module make
(9) Do not attempt to disassemble or process the LCD module.
(10) NC terminal should be open. Do not connect anything.
(11) If the logic circuit power is off, do not apply the input signals.
(12) Electro-Static Discharge Control，Since this module uses a CMOS LSI, the same careful
- Isopropyl alcohol
- Ethyl alcohol
- Water
- Ketone
- Aromatic solvents
- Before remove LCM from its packing case or incorporating it into a set, be sure the module
- Tools required for assembling, such as soldering irons, must be properly grounded. Assure
- To reduce the amount of static electricity generated, do not conduct assembling and other
- The LCD module is coated with a film to protect the display surface. Exercise care when
23 |
P a g e