AT94K05AL ATMEL Corporation, AT94K05AL Datasheet - Page 98
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT94K05AL
Manufacturer Part Number
AT94K05AL
Description
Fpslic Devices Combine 5K Gates of Atmel's Patented AT40K Fpga Architecture, a 20 Mips Avr 8-bit Risc Microprocessor Core, Numerous Fixed Microcontroller Peripheries And up to 36K Bytes of Program And Data SRAM.
Manufacturer
ATMEL Corporation
Datasheet
1.AT94K05AL.pdf
(192 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
98
AT94K Series FPSLIC
• Bits 1..0 - PWM11, PWM10: Pulse Width Modulator Select Bits
These bits select PWM operation of Timer/Counter1 as specified in Table 27. This mode is
described on page 101.
Table 27. PWM Mode Select
Timer/Counter1 Control Register B – TCCR1B
• Bit 7 - ICNC1: Input Capture1 Noise Canceler (4 CKs)
When the ICNC1 bit is cleared (zero), the input capture trigger noise canceler function is dis-
abled. The input capture is triggered at the first rising/falling edge sampled on the PE7(ICP) –
input capture pin – as specified. When the ICNC1 bit is set (one), four successive samples are
measures on the PE7(ICP) – input capture pin, and all samples must be High/Low according
to the input capture trigger specification in the ICES1 bit. The actual sampling frequency is
XTAL clock frequency.
• Bit 6 - ICES1: Input Capture1 Edge Select
While the ICES1 bit is cleared (zero), the Timer/Counter1 contents are transferred to the Input
Capture Register – ICR1 – on the falling edge of the input capture pin – PE7(ICP). While the
ICES1 bit is set (one), the Timer/Counter1 contents are transferred to the Input Capture Reg-
ister – ICR1 – on the rising edge of the input capture pin – PE7(ICP).
• Bit 5 - ICPE: Input Captive Pin Enable
This bit must be set by the user to enable the Input Capture Function of timer1. Disabling pre-
vents unnecessary register copies during normal use of the PE7 port.
• Bit 4 - Res: Reserved Bit
This bit is reserved in the FPSLIC and will always read zero.
• Bit 3 - CTC1: Clear Timer/Counter1 on Compare Match
When the CTC1 control bit is set (one), the Timer/Counter1 is reset to $0000 in the clock cycle
after a compareA match. If the CTC1 control bit is cleared, Timer/Counter1 continues counting
and is unaffected by a compare match. When a prescaling of 1 is used, and the compareA
register is set to C, the timer will count as follows if CTC1 is set:
... | C-1 | C | 0 | 1 | ...
When the prescaler is set to divide by 8, the timer will count like this:
... | C-1, C-1, C-1, C-1, C-1, C-1, C-1, C-1 | C, C, C, C, C, C, C, C | 0, 0, 0, 0, 0, 0, 0, 0 | ...
In PWM mode, this bit has a different function. If the CTC1 bit is cleared in PWM mode, the
Timer/Counter1 acts as an up/down counter. If the CTC1 bit is set (one), the Timer/Counter
wraps when it reaches the TOP value. Refer to page 101 for a detailed description.
Bit
$2E ($4E)
Read/Write
Initial Value
PWM11
0
0
1
1
7
ICNC1
R/W
0
PWM10
0
1
0
1
6
ICES1
R/W
0
PWM operation of Timer/Counter1 is disabled
Timer/Counter1 is an 8-bit PWM
Timer/Counter1 is a 9-bit PWM
Timer/Counter1 is a 10-bit PWM
Description
5
ICPE
R/W
0
4
-
R
0
3
CTC1
R/W
0
2
CS12
R/W
0
1
CS11
R/W
0
Rev. 1138F–FPSLI–06/02
0
CS10
R/W
0
TCCR1B