LPC47M112 SMSC Corporation, LPC47M112 Datasheet - Page 64
![no-image](/images/no-image-200.jpg)
LPC47M112
Manufacturer Part Number
LPC47M112
Description
ENHANCED SUPER I/O CONTROLLER WITH LPC INTERFACE
Manufacturer
SMSC Corporation
Datasheet
1.LPC47M112.pdf
(208 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LPC47M112-MC
Manufacturer:
SMSC
Quantity:
2 592
Part Number:
LPC47M112-MC
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
LPC47M112-MW
Manufacturer:
SMSC
Quantity:
2 014
Company:
Part Number:
LPC47M112-MW
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
LPC47M112-MW
Manufacturer:
SMSC
Quantity:
20 000
- Current page: 64 of 208
- Download datasheet (2Mb)
Enhanced Super I/O Controller with LPC Interface
Datasheet
12 SERIAL PORT (UART)
The LPC47M112 incorporates two full function UARTs. They are compatible with the NS16450, the 16450 ACE
registers and the NS16C550A. The UARTS perform serial-to-parallel conversion on received characters and parallel-to-
serial conversion on transmit characters. The data rates are independently programmable from 460.8K baud down to
50 baud. The character options are programmable for 1 start; 1, 1.5 or 2 stop bits; even, odd, sticky or no parity; and
prioritized interrupts. The UARTs each contain a programmable baud rate generator that is capable of dividing the input
clock or crystal by a number from 1 to 65535. The UARTs are also capable of supporting the MIDI data rate. Refer to
the Configuration Registers for information on disabling, power down and changing the base address of the UARTs.
The interrupt from a UART is enabled by programming OUT2 of that UART to a logic "1". OUT2 being a logic "0"
disables that UART's interrupt. The second UART also supports IrDA, HP-SIR and ASK-IR modes of operation.
Note: The UARTs 1 and 2 may be configured to share an interrupt. Refer to the Configuration section for more
information.
REGISTER DESCRIPTION
Addressing of the accessible registers of the Serial Port is shown below. The base addresses of the serial ports are
defined by the configuration registers (see Configuration section). The Serial Port registers are located at sequentially
increasing addresses above these base addresses. The LPC47M112 contains two serial ports, each of which contain a
register set as described below.
The following section describes the operation of the registers.
RECEIVE BUFFER REGISTER (RB)
Address Offset = 0H, DLAB = 0, READ ONLY
This register holds the received incoming data byte. Bit 0 is the least significant bit, which is transmitted and received
first. Received data is double buffered; this uses an additional shift register to receive the serial data stream and convert
it to a parallel 8 bit word which is transferred to the Receive Buffer register. The shift register is not accessible.
TRANSMIT BUFFER REGISTER (TB)
Address Offset = 0H, DLAB = 0, WRITE ONLY
This register contains the data byte to be transmitted. The transmit buffer is double buffered, utilizing an additional shift
register (not accessible) to convert the 8 bit data word to a serial format. This shift register is loaded from the Transmit
Buffer when the transmission of the previous byte is complete.
INTERRUPT ENABLE REGISTER (IER)
Address Offset = 1H, DLAB = 0, READ/WRITE
SMSC DS – LPC47M112
*Note: DLAB is Bit 7 of the Line Control Register
DLAB*
X
X
X
X
X
X
X
0
0
0
1
1
A2
0
0
0
0
0
0
1
1
1
1
0
0
Table 28 - Addressing the Serial Port
A1
0
0
0
0
1
0
0
1
1
1
0
1
A0
0
0
1
0
0
1
0
1
0
1
0
1
Receive Buffer (read)
Transmit Buffer (write)
Interrupt Enable (read/write)
Interrupt Identification (read)
FIFO Control (write)
Line Control (read/write)
Modem Control (read/write)
Line Status (read/write)
Modem Status (read/write)
Scratchpad (read/write)
Divisor LSB (read/write)
Divisor MSB (read/write
Page 64
REGISTER NAME
Rev. 02/02/2005
Related parts for LPC47M112
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LPC-20-SPEC](/images/no-image3.png)
Part Number:
Description:
20w Single Output Swi Tching Power Supply Lpc-20 Ser I Es
Manufacturer:
Analog Technology, Inc.
Datasheet:
![LPC-LP-0.8DQEW](/images/no-image3.png)
Part Number:
Description:
Low-profile Coaxial Connectors
Manufacturer:
DDK Ltd.
Datasheet:
![LAN83C183-JD](/images/no-image3.png)
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N769TQFP](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47M102S-MC](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N267-MN](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![USB20H04-JD](/images/no-image3.png)
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37M602](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37B777](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37C672](/images/no-image3.png)
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
![COM90C66LJP](/images/no-image3.png)
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869TQFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![USB97C100QFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N227-MN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: