MT90401 Zarlink Semiconductor, MT90401 Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
MT90401
Manufacturer Part Number
MT90401
Description
Sonet/sdh System Synchronizer
Manufacturer
Zarlink Semiconductor
Datasheet
1.MT90401.pdf
(38 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT90401AB
Manufacturer:
ZARLINK
Quantity:
500
Company:
Part Number:
MT90401AB1
Manufacturer:
st
Quantity:
421
1.4
As shown in Figure 4, the DPLL of the MT90401 consists of a Phase Detector, Phase Slope Limiter, Loop Filter,
Digitally Controlled Oscillator, and a Control Circuit.
Phase Detector - the Phase Detector compares the virtual reference signal from the TIE Corrector circuit with the
feedback signal from the Frequency Select MUX circuit, and provides an error signal corresponding to the phase
difference between the two. This error signal is passed to the Phase Slope Limiter circuit. The Frequency Select
MUX allows the proper feedback signal to be externally selected (e.g., 8kHz, 1.544MHz, 2.048MHz or 19.44MHz).
Phase Slope Limiter - the Phase Slope Limiter receives the error signal from the Phase Detector and ensures that
the DPLL responds to all input transient conditions with a limited output phase slope. In SONET Mode the
maximum output phase slope is limited to 885ns/s as per Telcordia GR-253-CORE. In SDH Mode the maximum
output phase slope is 53ns per 1.326ms.
Loop Filter - the Loop Filter is a low pass filter, that defines the network jitter and wander transfer requirements for
all input reference frequencies (8kHz, 1.544MHz, 2.048MHz, or 19.44MHz). In SONET mode the loop filter has a
cut-off frequency of 70mHz to comply with Telcordia GR-253-CORE and GR-1244-CORE. In SDH mode the loop
filter has a cut-off frequency of 1.1Hz to comply with ITU-T G.813 Option 1 and GR-1244-CORE.
Control Circuit - the Control Circuit uses status and control information from the State Machine and the Input
Impairment Circuit to set the mode of the DPLL. The three possible modes are Normal, Holdover and Freerun.
Digitally Controlled Oscillator (DCO) - the DCO receives the limited and filtered signal from the Loop Filter, and
based on its value, generates a corresponding digital output signal. The synchronization method of the DCO is
dependent on the state of the MT90401.
In Normal Mode, the DCO provides an output signal which is frequency and phase locked to the selected input
reference signal.
In Holdover Mode, the DCO is free running at a frequency equal to the last locked frequency the DCO was
generating while in Normal Mode. In order to improve accuracy of the Holdover Mode the actual frequency sample
is taken 30 to 60ms before switching into holdover.
In Freerun Mode, the DCO is free running with an accuracy equal to the accuracy of the C20i 20MHz source.
Telcordia GR-253-CORE requires that, during recovery from holdover, SONET clocks not change their output
frequency at a rate faster than 2.9ppm per second. In SONET Mode the MT90401 limits the rate of change of its
output frequency (frequency slope) to less than 1.9ppm per second; this limit remains in place when the PLL is in
Fast Lock Mode.
Virtual Reference
Digital Phase Lock Loop (DPLL)
TIE Corrector
from
Frequency Select MUX
Feedback Signal
Detector
Phase
from
Figure 4 - DPLL Block Diagram
Phase Slope
Limiter
Zarlink Semiconductor Inc.
Input Impairment Monitor
MT90401
State Select
12
State Machine
from
State Select
Loop Filter
from
Controlled
Oscillator
Digitally
Control
Circuit
Output Interface Circuit
DPLL Reference
to
Data Sheet