NL10276BC20_07Y NEC, NL10276BC20_07Y Datasheet
NL10276BC20_07Y
Available stocks
Related parts for NL10276BC20_07Y
NL10276BC20_07Y Summary of contents
Page 1
... DOD-M-1348 (2nd edition) This DATA SHEET is updated document from PRELIMINARY DATA SHEET DOD-M-1289(1). All information is subject to change without notice. Please confirm the sales representative before starting to design your system. 1 NEC Corporation 2002, 2003 All rights reserved. Datasheet pdf - http://www.DataSheet4U.net/ ...
Page 2
... While NEC Corporation has been making continuous effort to enhance the reliability of its products, the possibility of failures cannot be eliminated entirely. To minimize risks of damage to property or injury to person arising from a failure in an NEC product, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. ...
Page 3
... CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS......................................................... 11 4.5.1 LCD panel signal processing board ............................................................................................. 11 4.5.2 Backlight lamp.............................................................................................................................12 4.5.3 Positions of a plug and a socket...................................................................................................12 4.5.4 Connection between receiver and transmitter for LVDS .............................................................13 4.6 DISPLAY COLORS AND INPUT DATA SIGNALS ..........................................................................14 4.7 DISPLAY POSITIONS.........................................................................................................................15 4.8 SCANNING DIRECTIONS .................................................................................................................15 4.9 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD ...........................16 4 ...
Page 4
OUTLINE 1.1 STRUCTURE AND PRINCIPLE NL10276BC20-07Y module is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight. ...
Page 5
GENERAL SPECIFICATIONS Display area Diagonal size of display Drive system Display color Pixel Pixel arrangement Dot pitch Pixel pitch Module size Weight Contrast ratio Viewing angle Designed viewing direction Polarizer surface Polarizer pencil-hardness Color gamut Response time Luminance ...
Page 6
... VCC Fuse FG Note1 Backlight inverter GNDB Note1 Note2 Note1: Connections between GND (Signal ground), FG (Frame ground) and VBLC (Lamp low voltage terminal) in the LCD module GND - FG GND - VBLC FG - VBLC Note2: These grounds should be connected together in customer equipment. Power supply for gradation ...
Page 7
DETAILED SPECIFICATIONS 4.1 MECHANICAL SPECIFICATIONS Parameter Module size Display area Weight Note1: See "11. OUTLINE DRAWINGS". 4.2 ABSOLUTE MAXIMUM RATINGS Power supply voltage Input voltage for signals Storage temperature Operating temperature Relative humidity Absolute humidity Note1: Display signals ...
Page 8
... Sa: Waveform space for positive part, Sb: Waveform space for negative part Note3: The lamp holder of this product contains two backlight lamps. The low voltage terminal of both lamps is connected to one contact point. Also above power supply current specification is one lamp duty. Therefore, this lamp holder becomes twice as many power supply current as above value on low voltage (Cold) line ...
Page 9
Power supply voltage ripple This product works, even if the ripple voltage levels are beyond the permissible values as following the table, but there might be noise on the display image. Parameter VCC Note1: The permissible ripple voltage ...
Page 10
POWER SUPPLY VOLTAGE SEQUENCE 4.4.1 Sequence for LCD panel signal processing board VCC Note1 Display and function signals Note2 Note1: In terms of voltage variation (voltage drop) while VCC rising edge is below 3.0V, a protection circuit may ...
Page 11
... 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS 4.5.1 LCD panel signal processing board CN1 socket (Module side): FI-SE20P-HF (Japan Aviation Electronics Industry Limited) Adaptable plug: FI-S20S (Japan Aviation Electronics Industry Limited) Pin No. Symbol 1 GND 2 GND 3 DPSR 4 NC ...
Page 12
Backlight lamp CN2 plug: BHR-03VS-1 (J.S.T Mfg. Co., Ltd.) Adaptable socket: SM03 (4.0) B-BHS-TB (J.S.T Mfg. Co., Ltd.) Pin No. Symbol 1 VBLC 2 VBLH 3 VBLH 4.5.3 Positions of a plug and a socket 1 3 CN2 ...
Page 13
... Connection between receiver and transmitter for LVDS “High” “High” or “Low” DE CLK VCC (+3.3V) GND ViFD Note1: Recommended transmitter See the data sheet for THC63LVDM63A (THine Electronics Inc.). Note2: TC4 must be fixed to “High”. ...
Page 14
4.6 DISPLAY COLORS AND INPUT DATA SIGNALS This product can display in equivalent to 262,144 colors in 64 scale. Also the ...
Page 15
DISPLAY POSITIONS The following table is the coordinates per pixel (See figure of "4.8 SCANNING DIRECTIONS".). C(1023, 0) C(1022 4.8 SCANNING DIRECTIONS The following figures are seen ...
Page 16
INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD 4.9.1 Outline of input signal timings Horizontal signal Data enable (DE) Display period Note1 Note1: This diagram indicates virtual signal for set up to timing. Vertical signal Data enable ...
Page 17
Detail of A part VDRH CLK 0.5VCC VDRL VDRH DATA (R0 to R5) (G0 to G5) (B0 to B5) VDRL VDRH DE VDRL Note1 data number from 1 to 1022. See "4.8 SCANNING DIRECTIONS". 4.9.3 Timing characteristics ...
Page 18
OPTICS 4.10.1 Optical characteristics Parameter Note1 Luminance Contrast ratio Luminance uniformity Reference data Parameter Note1 Chromaticity Color gamut Response time Viewing angle Note1: Measurement conditions are as follows VCC = 3.3V, IBL = 5.0mArms/lamp, ...
Page 19
Definition of contrast ratio The contrast ratio is calculated by using the following formula. Contrast ratio (CR) = 4.10.3 Definition of luminance uniformity The luminance uniformity is calculated by using following formula. Luminance uniformity (LU) = The luminance ...
Page 20
... If customer touches it, products may be broken down or out of adjustment, because of stress to mounting parts. Do not hook cables nor pull connection cables such as flexible cable and so on, for fear of damage. If customer puts down the product temporarily, the product puts on flat subsoil as a display side turns down ...
Page 21
... Pay attention not to insert waste materials inside of products, if customer uses screwnails. Pack the product with original shipping package, because of avoidance of some damages during transportation, when customer returns it to NEC Corporation for repair and so on. PRELIMINARY DATA SHEET DOD-M-1348 (2nd edition) ...
Page 22
OUTLINE DRAWINGS 6.1 FRONT VIEW PRELIMINARY DATA SHEET DOD-M-1348 (2nd edition) NL10276BC20-07Y Unit ...
Page 23
REAR VIEW PRELIMINARY DATA SHEET DOD-M-1348 (2nd edition) NL10276BC20-07Y Unit ...
Page 24
The inside of latest specifications is revised to the clerical error, undecided mater (TBD, etc.) and the major improvement of previous edition. Only a changed part such as functions, characteristic value and so on that may affect a design ...