bsv-1.5s12r0h XP Power Limited, bsv-1.5s12r0h Datasheet - Page 12

• Manufacturer Part Number: bsv-1.5s12r0h
• Description: Pol Dc-dc Converter
• Manufacturer: XP Power Limited

BSV-H series is a small size(23.0x27.0x4mm size) and light weight(4.0g) step-down DC-DC converter, which has
achieved 22A. Since it can correspond from ultra low output voltage of 0.6V, and set accuracy of output voltage is
under ±1%, it can be used for the latest DSP, ASIC and FPGA applications. Due to high efficiency and high-speed
response by synchronous rectification circuit technology, saving space by no external components, and with SMD
package etc. an excellent performance beyond our common sense has been achieved.
<Features>
-Ultra Small Size 23x27mm
-Low Profile 4.0mm
-High-Speed Load Response
-Output Voltage Accuracy ±1%
-Ultra High Efficiency
-Built in Over-Current Protection
-Under Voltage Lock Out
-Remote ON/OFF Control
<Model / Rating>
Note1 : The value of ripple and noise and efficiency is the one at input voltage (5V) and rating load.
Note2 : Measurements of ripple noise is performed at BW=20MHz, with an additional multilayer ceramic capacitor of 47μF to
Note3 : Depending on the ambient air temperature conditions, air flow is required.
<Specification>
BSV-1.5S22R0H
*The above specification is provided with rating value, unless otherwise specified
Rating Input Voltage/ Range
Rating Output Voltage
Adjustable Output Voltage
Range
Line Regulation
Load Regulation
Temperature Coefficient
Ripple Noise
Efficiency
Turn-On Transient
Max. Output Capacitance
Over-Current Protection
Over-Voltage Protection
Under Voltage Lock Out
Remote On/Off Control
Standby Current
P-Good Signal
Remote Sensing
Operating Temp. Range
Storage Temp. Range
Humidity Range
Storage Condition
Cooling Condition
Vibration
Shock
Weight
Outline
Model
the input and 22μF to the output.
DC-DC Converter
The Fifth Generation, Ultra Small Size, Isolated DC-DC Converter
3.0 to 5.5
Input V
Vdc
0.5% typ. (Rating output, for the regulation of input voltage range on table 1)
0.5% typ. (Rating input/output voltage, for the regulation of load 0-100%)
Refer to Table 1 (Input/output rating, normal temperature and Bw=20MHz)
-40°C to +85°C (Refer to thermal derating graph)
Refer to thermal derating graph
Refer to Table 1
+1.5V±1%(Trim Pin at open)
0.6~1.5V
±0.02%/°C typ. (Input/output rating, for the regulation of operating temp. range -40°C to +50°C)
87% typ. (Input/output rating, normal temperature. Refer to table 1)
0.5ms typ. (Resistance load)
4700μF max.
Operates at 105% or more rating load current, auto recovery type. Avoid long time short-circuit
condition.
None
Available
Between 10pin (ON/OFF) and –6, 9pin (GND): output goes ON when in open, output goes
OFF when in short
0.2mA typ.
At normal output: high, at output decrease: low, (This terminal is open-drain.)
Available
-40°C to +85°C
20%-95%R.H. max. (Max. wet bulb 35°C, non-condensing)
For the converter before being mounted, store at 30°C/60% R.H. or below
5-10Hz All amplitude 10mm, 10-55Hz acceleration 2G (1 hour in each of 3 orthogonal axes)
Acceleration 20G (3 directions, 3 times each, total : 18 times), Shocking time 11±5ms
4.0g typ.
SMD type W=23.0 L=27.0 H=4.0 typ. (mm) (For detail dimensions refer to the outline)
-Adjustable Output Voltage
-Surface Mount Package (SMD)
-External Capacitors not required
-Heat Sink not required
-Non-Isolated Type
-Operating Temp. Range –40°C to +85°C
(Temp. Derating required)
-RoHS Compliance
Preliminary
Output V
Vdc
1.5
Output I
0 to 22
A
BSV-H22A Series
Output ADJ
0.6 to 1.5
Vdc
mVpp(typ.)
Noise
30
BDD20080618
Efficiency
%(typ.)
Table 1
87
Table2