adc08d1010diyb National Semiconductor Corporation, adc08d1010diyb Datasheet - Page 12

• Manufacturer Part Number: adc08d1010diyb
• Description: High Performance, Low Power, Dual 8-bit, 1 Gsps A/d Converter
• Manufacturer: National Semiconductor Corporation

www.national.com
t
t
t
t
f
t
t
t
t
t
t
AD
AJ
OD
WU
SCLK
SSU
SH
CAL
CAL_L
CAL_H
CalDly
Symbol
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. There is no guarantee of operation at the Absolute Maximum
Ratings. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications
and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics
may degrade when the device is not operated under the listed test conditions.
Note 2: All voltages are measured with respect to GND = DR GND = 0V, unless otherwise specified.
Note 3: When the input voltage at any pin exceeds the power supply limits (that is, less than GND or greater than V
25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to
two. This limit is not placed upon the power, ground and digital output pins.
Note 4: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through ZERO Ohms.
Note 5: See AN-450, “Surface Mounting Methods and Their Effect on Product Reliability”.
Note 6: The analog inputs are protected as shown below. Input voltage magnitudes beyond the Absolute Maximum Ratings may damage this device.
Sampling (Aperture) Delay
Aperture Jitter
Input Clock to Data Output Delay
(in addition to Pipeline Delay)
Pipeline Delay (Latency)
(Notes 11, 14)
Over Range Recovery Time
PD low to Rated Accuracy
Conversion (Wake-Up Time)
DCS
Serial Clock Frequency
Data to Serial Clock Setup Time (Note 11)
Data to Serial Clock Hold Time
Serial Clock Low Time
Serial Clock High Time
Calibration Cycle Time
CAL Pin Low Time
CAL Pin High Time
Calibration delay determined by
pin 127 state.
Parameter
Input CLK+ Fall to Acquisition of Data
50% of Input Clock transition to 50% of
Data transition
DI Outputs
DId Outputs
DQ Outputs
DQd Outputs
Differential V
get accurate conversion
(Note 11)
(Note 11)
(Note 11)
See Figure 9(Note 11)
See Figure 9(Note 11)
CalDly = Low
See 1.1.1 Self Calibration, Figure 9,
(Note 11)
CalDly = High
See 1.1.1, Self Calibration, Figure 9,
(Note 11)
IN
Conditions
step from ±1.2V to 0V to
12
Normal Mode
DES Mode
Normal Mode
DES Mode
20146704
1.4 x 10
(Note 8)
Typical
500
100
1.3
0.4
3.1
2.5
1
1
1
A
), the current at that pin should be limited to
5
(Note 8)
Limits
13.5
14.5
2
2
13
14
13
14
80
80
4
4
25
31
Clock Cycles
Clock Cycles
Clock Cycles
Clock Cycles
Clock Cycles
Input Clock
Input Clock
(Limits)
ns (min)
ns (min)
ns (min)
ns (min)
ps rms
Cycles
(max)
Units
Cycle
(min)
(min)
(min)
MHz
ns
ns
ns
µs