isp1582 NXP Semiconductors, isp1582 Datasheet - Page 5

no-image

isp1582

Manufacturer Part Number
isp1582
Description
Hi-speed Universal Serial Bus Peripheral Controller
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISP1582
Manufacturer:
ST
0
Part Number:
isp1582BE
Quantity:
1 782
Part Number:
isp1582BS
Manufacturer:
PHILPS
Quantity:
1 500
Part Number:
isp1582BS
Manufacturer:
PHI/PBF
Quantity:
894
Part Number:
isp1582BS
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
isp1582BSUM
Manufacturer:
INTEL
Quantity:
828
NXP Semiconductors
ISP1582_6
Product data sheet
Table 2.
Symbol
RESET_N
EOT
DREQ
DACK
DIOR
DIOW
DGND
INT
CS_N
RD_N
WR_N
A0
A1
A2
V
A3
CC(I/O)
[3]
[1]
Pin description
Pin
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Rev. 06 — 20 September 2007
Type
I
I
O
I
I
I
-
O
I
I
I
I
I
I
-
I
…continued
[2]
Description
reset input (500 s); a LOW level produces an asynchronous
reset; connect to V
When the RESET_N pin is LOW, ensure that the WAKEUP pin
does not goes from LOW to HIGH; otherwise the device will
enter test mode.
TTL; 5 V tolerant
end-of-transfer input (programmable polarity); when not in use,
connect this pin to V
input pad; TTL; 5 V tolerant
DMA request (programmable polarity) output; when not in use,
connect this pin to ground through a 10 k resistor; see
Table 50
TTL; 4 ns slew-rate control
DMA acknowledge input (programmable polarity); when not in
use, connect this pin to V
Table 50
TTL; 5 V tolerant
DMA read strobe input (programmable polarity); when not in
use, connect this pin to V
Table 50
TTL; 5 V tolerant
DMA write strobe input (programmable polarity); when not in
use, connect this pin to V
Table 50
TTL; 5 V tolerant
digital ground
interrupt output; programmable polarity (active HIGH or LOW)
and signaling (edge or level triggered)
CMOS output; 8 mA drive
chip select input
input pad; TTL; 5 V tolerant
read strobe input
input pad; TTL; 5 V tolerant
write strobe input
input pad; TTL; 5 V tolerant
bit 0 of the address bus
input pad; TTL; 5 V tolerant
bit 1 of the address bus
input pad; TTL; 5 V tolerant
bit 2 of the address bus
input pad; TTL; 5 V tolerant
supply voltage; used to supply voltage to the I/O pads; see
Section 7.16
bit 3 of the address bus
input pad; TTL; 5 V tolerant
and
and
and
and
Table 51
Table 51
Table 51
Table 51
CC
CC(I/O)
for power-on reset (internal POR circuit)
Hi-Speed USB Peripheral Controller
CC(I/O)
CC(I/O)
CC(I/O)
through a 10 k resistor
through a 10 k resistor; see
through a 10 k resistor; see
through a 10 k resistor; see
© NXP B.V. 2007. All rights reserved.
ISP1582
5 of 69

Related parts for isp1582