lan8187 Standard Microsystems Corp., lan8187 Datasheet - Page 53

• Manufacturer Part Number: lan8187
• Description: Lan8187/lan8187i ?15kv Esd Protected Mii/rmii 10/100 Ethernet Transceiver With Hp Auto-mdix & Flexpwr Technology
• Manufacturer: Standard Microsystems Corp.

±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX & flexPWR
Datasheet
SMSC LAN8187/LAN8187i
5.4.7
5.4.8
5.4.8.1
5.4.9
5.4.9.1
5.4.9.2
LED Description
The PHY provides four LED signals. These provide a convenient means to determine the mode of
operation of the Phy. All LED signals are either active high or active low.
The four LED signals can be either active-high or active-low. Polarity depends upon the Phy address
latched in on reset. The LAN8187/LAN8187i senses each Phy address bit and changes the polarity of
the LED signal accordingly. If the address bit is set as level “1”, the LED polarity will be set to an active-
low. If the address bit is set as level “0”, the LED polarity will be set to an active-high.
The ACTIVITY LED output is driven active when CRS is active (high). When CRS becomes inactive,
the Activity LED output is extended by 128ms.
The LINK LED output is driven active whenever the PHY detects a valid link. The use of the 10Mbps
or 100Mbps link test status is determined by the condition of the internally determined speed selection.
The SPEED100 LED output is driven active when the operating speed is 100Mbit/s or during Auto-
negotiation. This LED will go inactive when the operating speed is 10Mbit/s or during line isolation
(register 31 bit 5).
The Full-Duplex LED output is driven active low when the link is operating in Full-Duplex mode.
Loopback Operation
The 10/100 digital has two independent loop-back modes: Internal loopback and far loopback.
Internal Loopback
The internal loopback mode is enabled by setting bit register 0 bit 14 to logic one. In this mode, the
scrambled transmit data (output of the scrambler) is looped into the receive logic (input of the
descrambler). The COL signal will be inactive in this mode, unless collision test (bit 0.7) is active.
In this mode, during transmission (TX_EN is HIGH), nothing is transmitted to the line and the
transmitters are powered down.
Configuration Signals
The PHY has 11 configuration signals whose inputs should be driven continuously, either by external
logic or external pull-up/pull-down resistors.
Physical Address Bus - PHYAD[4:0]
The PHYAD[4:0] signals are driven high or low to give each PHY a unique address. This address is
latched into an internal register at end of hardware reset. In a multi-PHY application (such as a
repeater), the controller is able to manage each PHY via the unique address. Each PHY checks each
management data frame for a matching address in the relevant bits. When a match is recognized, the
PHY responds to that particular frame. The PHY address is also used to seed the scrambler. In a multi-
PHY application, this ensures that the scramblers are out of synchronization and disperses the
electromagnetic radiation across the frequency spectrum.
Mode Bus – MODE[2:0]
The MODE[2:0] bus controls the configuration of the 10/100 digital block. When the nRST pin is
deasserted, the register bit values are loaded according to the MODE[2:0] pins. The 10/100 digital
block is then configured by the register bit values. When a soft reset occurs (bit 0.15) as described in
Table
MODE[2:0] pins have no affect.
5.30, the configuration of the 10/100 digital block is controlled by the register bit values, and the
DATASHEET
53
TM
Technology
Revision 1.5 (01-10-08)