lan9313 Standard Microsystems Corp., lan9313 Datasheet - Page 386

• Manufacturer Part Number: lan9313
• Description: Lan9313/lan9313i Three Port 10/100 Managed Ethernet Switch With Mii
• Manufacturer: Standard Microsystems Corp.

Chapter 14 Operational Characteristics
Revision 1.2 (04-08-08)
14.1
14.2
Supply Voltage (VDD33A1, VDD33A2, VDD33BIAS, VDD33IO)
Positive voltage on signal pins, with respect to ground
Negative voltage on signal pins, with respect to ground
Positive voltage on XI, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XO, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (T
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 14.1 When powering this device from laboratory or system power supplies, it is important that
Note 14.2 This rating does not apply to the following pins: XI, XO, EXRES.
Note 14.3 This rating does not apply to the following pins: EXRES.
Note 14.4 0
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 14.2, "Operating
section of this specification is not implied. Note, device signals are NOT 5 volt tolerant.
Supply Voltage (VDD33A1, VDD33A2, VDD33BIAS, VDD33IO). . . . . . . . . . . . . . . . . +3.3V +/- 300mV
Ambient Operating Temperature in Still Air (T
**Proper operation of the LAN9313/LAN9313i is guaranteed only within the ranges specified in this
section.
Absolute Maximum Ratings*
Operating Conditions**
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
(LAN9313I)
o
C to +70
o
C for commercial version (LAN9313), -40
Conditions**",
DATASHEET
Section 14.4, "DC
386
A
A
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(Note
(Note
Specifications", or any other applicable
14.2) . . . . . . . . . . . . . . . . . . . . . . . . . +6V
Three Port 10/100 Managed Ethernet Switch with MII
14.3) . . . . . . . . . . . . . . . . . . . . . . . -0.5V
(Note
o
C to +85
14.1) . . . . . . . . . . . 0V to +3.6V
o
SMSC LAN9313/LAN9313i
C for industrial version
o
C to +150
Note 14.4
Note 14.4
Datasheet
o
C