lan9313 Standard Microsystems Corp., lan9313 Datasheet - Page 45
lan9313
Manufacturer Part Number
lan9313
Description
Lan9313/lan9313i Three Port 10/100 Managed Ethernet Switch With Mii
Manufacturer
Standard Microsystems Corp.
Datasheet
1.LAN9313.pdf
(398 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lan9313-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
lan9313-NZW
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
lan9313I-NZW
Manufacturer:
Standard
Quantity:
261
Company:
Part Number:
lan9313I-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
lan9313NZW
Manufacturer:
Standard
Quantity:
295
- Current page: 45 of 398
- Download datasheet (5Mb)
Three Port 10/100 Managed Ethernet Switch with MII
Datasheet
SMSC LAN9313/LAN9313i
4.2.4
4.2.4.1
STRAP NAME
LED_en_strap[7:0]
LED_fun_strap[1:0]
Configuration Straps
Configuration straps allow various features of the LAN9313/LAN9313i to be automatically configured
to user defined values. Configuration straps can be organized into two main categories: hard-straps
and soft-straps. Both hard-straps and soft-straps are latched upon Power-On Reset (POR) or pin reset
(nRST). The primary difference between these strap types is that soft-strap default values can be
overridden by the EEPROM Loader, while hard-straps cannot.
Configuration straps which have a corresponding external pin include internal resistors in order to
prevent the signal from floating when unconnected. If a particular configuration strap is connected to
a load, an external pull-up or pull-down resistor should be used to augment the internal resistor to
ensure that it reaches the required voltage level prior to latching. The internal resistor can also be
overridden by the addition of an external resistor.
Note: The system designer must guarantee that configuration strap pins meet the timing
Soft-Straps
Soft-strap values are latched on the release of POR or nRST and are overridden by values from the
EEPROM Loader (when an EEPROM is present). These straps are used as direct configuration values
or as defaults for CPU registers. Some, but not all, soft-straps have an associated pin. Those that do
not have an associated pin, have a tie off default value. All soft-strap values can be overridden by the
EEPROM Loader.
Straps which have an associated pin are also fully defined in
Configuration," on page
the operation of the EEPROM Loader and the loading of strap values.
Upon setting the DIGITAL_RST bit in the
RELOAD command via the
original latched (non-overridden) values if an EEPROM is no longer attached or has been erased. The
associated pins are not re-sampled. (i.e. The value latched on the pin during the last POR or nRST
will be used, not the value on the pin during the digital reset or RELOAD command issuance). If it is
desired to re-latch the current configuration strap pin values, a POR or nRST must be issued.
requirements specified in
If configuration strap pins are not at the correct voltage level prior to being latched, the
LAN9313/LAN9313i may capture incorrect strap values.
Table 4.2 Soft-Strap Configuration Strap Definitions
Table 4.2
DESCRIPTION
LED Enable Straps: Configures the default value for the
LED_EN bits in the
(LED_CFG). A high value configures the associated
LED/GPIO pin as a LED. A low value configures the
associated LED/GPIO pin as a GPIO.
Note:
LED Function Straps: Configures the default value for the
LED_FUN bits in the
(LED_CFG). When configured low, the corresponding bit
will be cleared. When configured high, the corresponding
bit will be set.
26. Refer to
One pin configures the default for all 8
LED/GPIOs, but 8 separate bits are loaded by the
EEPROM Loader, allowing individual control over
each LED/GPIO.
provides a list of all soft-straps and their associated pin or default value.
EEPROM Command Register
Section 14.5.2, "Reset and Configuration Strap Timing," on page
DATASHEET
Section 8.2.4, "EEPROM Loader," on page 113
LED Configuration Register
LED Configuration Register
45
Reset Control Register (RESET_CTL)
(E2P_CMD), these straps return to their
Chapter 3, "Pin Description and
PIN / DEFAULT
VALUE
LED_EN
LED_FUN[1:0]
Revision 1.2 (04-08-08)
or upon issuing a
for information on
390.
Related parts for lan9313
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: