lpc4310 NXP Semiconductors, lpc4310 Datasheet - Page 10

• Manufacturer Part Number: lpc4310
• Description: Lpc4350/30/20/10 32-bit Arm Cortex-m4/m0 Mcu; Up To 264 Kb Sram; Ethernet; Two High-speed Usbs; Advanced Configurable Peripherals
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
LPC4350_30_20_10
Objective data sheet
Symbol
P2_6
P2_7
P2_8
P2_9
P2_10
P2_11
P2_12
P2_13
P3_0
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[2]
Pin description
LBGA256
pin
K16
H14
J16
H16
G16
F16
E15
C16
F13
…continued
Reset
state
<tbd>
I; PU
<tbd>
I; PU
I; PU
I; PU
I; PU
I; PU
<tbd>
Type Description
I/O
I/O
I/O
O
I/O
O
I/O
I/O
I/O
O
I/O
I/O
I/O
O
I/O
I/O
I/O
O
O
I/O
I/O
O
I
I/O
I/O
O
-
I/O
I/O
I
-
I/O
I/O
O
I/O
O
All information provided in this document is subject to legal disclaimers.
SGPIO7 — General purpose digital input/output pin.
U0_DIR — RS-485/EIA-485 output enable/direction control for USART0.
EXTBUS_A10 — External memory address line 10.
USB0_IND0 — <tbd>.
GPIO0[7] — General purpose digital input/output pin. This pin is sampled at
RESET for ISP entry.
CTOUT_1 — SCT output 1. Match output 1 of timer 0.
U3_UCLK — Serial clock input/output for USART3 in synchronous mode.
EXTBUS_A9 — External memory address line 9.
SGPIO15 — General purpose digital input/output pin.
CTOUT_0 — SCT output 0. Match output 0 of timer 0.
U3_DIR — RS-485/EIA-485 output enable/direction control for USART3.
EXTBUS_A8 — External memory address line 8. Boot control pin 2.
GPIO1[10] — General purpose digital input/output pin.
CTOUT_3 — SCT output 3. Match output 3 of timer 0.
U3_BAUD — <tbd> for USART3.
EXTBUS_A0 — External memory address line 0.
GPIO0[14] — General purpose digital input/output pin.
CTOUT_2 — SCT output 2. Match output 2 of timer 0.
U2_TXD — Transmitter output for USART2.
EXTBUS_A1 — External memory address line 1.
GPIO1[11] — General purpose digital input/output pin.
CTOUT_5 — SCT output 5. Match output 1 of timer 1.
U2_RXD — Receiver input for USART2.
EXTBUS_A2 — External memory address line 2.
GPIO1[12] — General purpose digital input/output pin.
CTOUT_4 — SCT output 4. Match output 0 of timer 1.
n.c.
EXTBUS_A3 — External memory address line 3.
GPIO1[13] — General purpose digital input/output pin.
CTIN_4 — SCT input 4. Capture input 2 of timer 1.
n.c.
EXTBUS_A4 — External memory address line 4.
I2S0_TX_SCK — Receive Clock. It is driven by the master and received by
the slave. Corresponds to the signal SCK in the I
I2S0_RX_MCLK — I2S0 receive master clock.
I2S0_RX_SCK — I2S0 transmit clock. It is driven by the master and
received by the slave. Corresponds to the signal SCK in the I
specification.
I2S0_TX_MCLK — I2S0 transmit master clock.
Rev. 1 — 29 October 2010
32-bit ARM Cortex-M4/M0 microcontroller
LPC4350/30/20/10
2
S-bus specification.
© NXP B.V. 2010. All rights reserved.
2
S-bus
10 of 85