uaa3535hl NXP Semiconductors, uaa3535hl Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
uaa3535hl
Manufacturer Part Number
uaa3535hl
Description
Low Power Gsm/dcs/pcs Multi-band Transceiver
Manufacturer
NXP Semiconductors
Datasheet
1.UAA3535HL.pdf
(24 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Philips Semiconductors
IF
The IF divider can be programmed to divide the integrated
IF VCO frequency by 1 or 2. The selection of these
2 modes is accomplished by the control bit IFDIV;
see Table 8.
Table 8 IF divider control
TXIF
The transmit section integrates two switchable low-pass
filters, one for a 45.5 MHz IF and the other one for
91 MHz IF. The selection of these 2 modes is
accomplished by the control bit FILT; see Table 9.
Table 9 TXIF filter control
IF
The IF synthesizer divider can be programmed to divide
the semi-integrated IF VCO frequency by 6 or 7.
The selection of these 2 modes is accomplished by the
control bit IFO; see Table 10.
Table 10 IF synthesizer divider control
2000 Feb 17
Low power GSM/DCS/PCS multi-band transceiver
DIVIDER CONTROL
SYNTHESIZER DIVIDER CONTROL
FILTER CONTROL
BIT IFDIV
BIT FILT
BIT IFO
0
1
0
1
0
1
IF = f
IF = f
IF 45.5 MHz
IF 91 MHz
divide-by-6
divide-by-7
TXIF FILTER MODE
IF DIVIDER MODE
IF SYNTHESIZER
VCO
VCO
DIVIDER MODE
divided by 2
8
Programming
S
A simple 3-wire unidirectional serial bus is used to program
the circuit. The 3 lines are DATA, CLK and E (enable).
The data sent to the device is loaded in bursts framed
by E. Programming clock edges are ignored until E goes
active LOW. The programmed information is loaded into
the addressed latch when E returns inactive HIGH. This is
allowed when CLK is in either state without causing any
consequences to the register data. Only the last 17 bits
serially clocked into the device are retained within the
programming register. Additional leading bits are ignored,
and no check is made on the number of clock pulses.
The fully static CMOS design uses virtually no current
when the bus is inactive. It can always capture new
programming data even during power-down of both
synthesizers.
D
Data is entered with the most significant bit first.
The leading bits make up the data field, while the trailing
4 bits are an address field. The address bits are decoded
on the rising edge of E. This produces an internal load
pulse to store the data in the addressed latch. To ensure
that data is correctly loaded on first power-up, E should be
held LOW and only taken High after having programmed
an appropriate register. To avoid erroneous divider ratios,
the pulse is inhibited during the period when data is read
by the frequency dividers. This condition is guaranteed by
respecting a minimum E pulse width after data transfer.
The allocation of the register bits is given in Table 11.
R
The UAA3535HL programming registers have a preset
state. The preset values can be found in Table 12.
Conditions for guaranteed preset values at power-on are
as follows:
ERIAL PROGRAMMING BUS
ATA FORMAT
EGISTER PRESET CONDITIONS
DATA, CLOCK, E, SYNON, RXON and TXON must be
at 0 V
Preset value is guaranteed 2 ms after V
to 90% of 2.6 V
E should stay at 0 V up to the end of the first
programming word.
Objective specification
UAA3535HL
CC(SYN)
rises