k4d261638k Samsung Semiconductor, Inc., k4d261638k Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
k4d261638k
Manufacturer Part Number
k4d261638k
Description
128mbit Gddr Sdram
Manufacturer
Samsung Semiconductor, Inc.
Datasheet
1.K4D261638K.pdf
(18 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
k4d261638k-LC40
Manufacturer:
SAMSUNG
Quantity:
12 046
Company:
Part Number:
k4d261638k-LC40
Manufacturer:
SAMSUNG
Quantity:
3 120
Company:
Part Number:
k4d261638k-LC50
Manufacturer:
SAMSUNG
Quantity:
12 051
Company:
Part Number:
k4d261638k-LC50
Manufacturer:
SAMSUNG
Quantity:
11 350
cycle before the interrupting read data appear on the outputs to avoid data contention. When the read command is registered, any
residual data from the burst write cycle must be masked by DM. The delay from the last data to read command (tCDLR) is required to
avoid the data contention DRAM inside. Data that are presented on the DQ pins before the read command is initiated will actually be
written to the memory. Read command interrupting write can not be issued at the next clock edge of that of write command.
7.4 WRITE INTERRUPTED BY A READ
The following function established how a Read command may interrupt a Write burst and which input data is not written into the memory.
1. For Read commands interrupting a Write burst, the minimum Write to Read command delay is 2 clock cycles. The case where the Write to Read delay
2. For Read commands interrupting a Write burst, the DM pin must be used to mask the input data words whcich immediately precede the interrupting
3. For all cases of a Read interrupting a Write, the DQ and DQS buses must be released by the driving chip (i.e., the memory controller) in time to allow
4. If input Write data is masked by the Read command, the DQS input is ignored by the DDR SDRAM.
5. Refer to "3.3.2 Burst write operation"
8.0 ABSOLUTE MAXIMUM RATINGS
Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
K4D261638K
Voltage on any pin relative to Vss
Voltage on V
Voltage on V
Storage temperature
Power dissipation
Short circuit current
A burst write can be interrupted by a read command of any bank. The DQ’s must be in the high impedance state at least one clock
CMD
is 1 clock cycle is disallowed
Read operation and the input data word which immediately follows the interrupting Read operation
the buses to turn around before the DDR SDRAM drives them during a read operation.
DQS
DQ ′s
CK
CK
DM
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
NOP
DD
DD
< Burst Length=8, CAS Latency=3 >
0
Parameter
supply relative to Vss
supply relative to Vss
t
WPRES
WRITE
1
t
DQSSmax
t
WPREH
NOP
Din 0
2
Din 1
NOP
Din 2
3
Din 3
V
Symbol
IN
V
T
V
NOP
, V
I
P
DDQ
STG
OS
DD
Din 4
D
OUT
t
4
WR
- 10 /19 -
Din 5
NOP
Din 6
5
Din 7
NOP
6
-55 ~ +150
-0.5 ~ 3.6
-1.0 ~ 3.6
-0.5 ~ 3.6
Value
2.0
READ
50
7
128M GDDR SDRAM
NOP
8
Rev. 1.3 July 2007
NOP
Unit
mA
°C
W
V
V
V
NOP
Dout 0