PIC18F2450 MICROCHIP [Microchip Technology], PIC18F2450 Datasheet - Page 134

• Manufacturer Part Number: PIC18F2450
• Description: 28/40/44-Pin, High-Performance, 12 MIPS, Enhanced Flash, USB Microcontrollers with nanoWatt Technology
• Manufacturer: MICROCHIP [Microchip Technology]

PIC18F2450/4450
REGISTER 14-2:
There are 6 signals from the module to communicate
with and control an external transceiver:
• VM: Input from the single-ended D- line
• VP: Input from the single-ended D+ line
• RCV: Input from the differential receiver
• VMO: Output to the differential line driver
• VPO: Output to the differential line driver
• UOE: Output enable
DS39760A-page 132
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1-0
Note 1:
UTEYE
R/W-0
2:
3:
If UTRDIS is set, the UOE signal will be active independent of the UOEMON bit setting.
The UPUEN, UTRDIS and FSEN bits should never be changed while the USB module is enabled. These
values must be preconfigured prior to enabling the module.
This bit is only valid when the on-chip transceiver is active (UTRDIS = 0); otherwise, it is ignored.
UTEYE: USB Eye Pattern Test Enable bit
1 = Eye pattern test enabled
0 = Eye pattern test disabled
UOEMON: USB OE Monitor Enable bit
1 = UOE signal active; it indicates intervals during which the D+/D- lines are driving
0 = UOE signal inactive
Unimplemented: Read as ‘0’
UPUEN: USB On-Chip Pull-up Enable bit
1 = On-chip pull-up enabled (pull-up on D+ with FSEN = 1 or D- with FSEN = 0)
0 = On-chip pull-up disabled
UTRDIS: On-Chip Transceiver Disable bit
1 = On-chip transceiver disabled; digital transceiver interface enabled
0 = On-chip transceiver active
FSEN: Full-Speed Enable bit
1 = Full-speed device: controls transceiver edge rates; requires input clock at 48 MHz
0 = Low-speed device: controls transceiver edge rates; requires input clock at 6 MHz
PPB1:PPB0: Ping-Pong Buffers Configuration bits
11 = Enabled for all endpoints except Endpoint 0
10 = Even/Odd ping-pong buffers enabled for all endpoints
01 = Even/Odd ping-pong buffer enabled for OUT Endpoint 0
00 = Even/Odd ping-pong buffers disabled
UOEMON
R/W-0
UCFG: USB CONFIGURATION REGISTER
(1)
W = Writable bit
‘1’ = Bit is set
U-0
—
Advance Information
(2)
UPUEN
R/W-0
(2,3)
(1)
(2,3)
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
UTRDIS
R/W-0
The VPO and VMO signals are outputs from the SIE to
the external transceiver. The RCV signal is the output
from the external transceiver to the SIE; it represents
the differential signals from the serial bus translated
into a single pulse train. The VM and VP signals are
used to report conditions on the serial bus to the SIE
that can’t be captured with the RCV signal. The
combinations of states of these signals and their
interpretation are listed in Table 14-1 and Table 14-2.
(2)
FSEN
R/W-0
(2)
© 2006 Microchip Technology Inc.
x = Bit is unknown
R/W-0
PPB1
R/W-0
PPB0
bit 0