PIC18F25J11-I/PT MICROCHIP [Microchip Technology], PIC18F25J11-I/PT Datasheet - Page 242

• Manufacturer Part Number: PIC18F25J11-I/PT
• Description: 28/44-Pin, Low-Power, High-Performance Microcontrollers with nanoWatt XLP Technology
• Manufacturer: MICROCHIP [Microchip Technology]

PIC18F46J11 FAMILY
REGISTER 17-1:
DS39932C-page 242
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5-4
bit 3-0
R/W-0
PxM1
PxM<1:0>: Enhanced PWM Output Configuration bits
If CCPxM<3:2> = 00, 01, 10:
xx = PxA assigned as capture/compare input/output; PxB, PxC and PxD assigned as port pins
If CCPxM<3:2> = 11:
00 = Single output: PxA, PxB, PxC and PxD controlled by steering (see Section 17.5.7 “Pulse Steering
01 = Full-bridge output forward: PxD modulated; PxA active; PxB, PxC inactive
10 = Half-bridge output: PxA, PxB modulated with dead-band control; PxC and PxD assigned as
11 = Full-bridge output reverse: PxB modulated; PxC active; PxA and PxD inactive
DCxB<1:0>: PWM Duty Cycle bit 1 and bit 0
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two LSbs of the 10-bit PWM duty cycle. The eight MSbs of the duty cycle are found
in CCPRxL.
CCPxM<3:0>: ECCPx Mode Select bits
0000 = Capture/Compare/PWM off (resets ECCPx module)
0001 = Reserved
0010 = Compare mode, toggle output on match
0011 = Capture mode
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4
0111 = Capture mode, every 16
1000 = Compare mode, initialize ECCPx pin low, set output on compare match (set CCPxIF)
1001 = Compare mode, initialize ECCPx pin high, clear output on compare match (set CCPxIF)
1010 = Compare mode, generate software interrupt only, ECCPx pin reverts to I/O state
1011 = Compare mode, trigger special event (ECCPx resets TMR1 or TMR3, starts A/D conversion,
1100 = PWM mode; PxA and PxC active-high; PxB and PxD active-high
1101 = PWM mode; PxA and PxC active-high; PxB and PxD active-low
1110 = PWM mode; PxA and PxC active-low; PxB and PxD active-high
1111 = PWM mode; PxA and PxC active-low; PxB and PxD active-low
R/W-0
PxM0
Mode”)
port pins
CCPxCON: ECCPx CONTROL (ACCESS FBAh/FB4h)
sets CCxIF bit)
W = Writable bit
‘1’ = Bit is set
DCxB1
R/W-0
DCxB0
th
R/W-0
th
rising edge
rising edge
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
CCPxM3
R/W-0
CCPxM2
R/W-0
© 2009 Microchip Technology Inc.
x = Bit is unknown
CCPxM1
R/W-0
CCPxM0
R/W-0
bit 0