FDC37B72X_07 SMSC [SMSC Corporation], FDC37B72X_07 Datasheet - Page 104
![no-image](/images/no-image-200.jpg)
FDC37B72X_07
Manufacturer Part Number
FDC37B72X_07
Description
128 Pin Enhanced Super I/O Controller with ACPI Support
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.FDC37B72X_07.pdf
(238 pages)
- Current page: 104 of 238
- Download datasheet (832Kb)
The interrupt generated is ISA friendly in that it
must pulse the interrupt line low, allowing for
interrupt sharing. After a brief pulse low following
the interrupt event, the interrupt line is tri-stated so
that other interrupts may assert.
An interrupt is generated when:
1. For DMA transfers: When serviceIntr is 0,
2. For Programmed I/O:
3. When nErrIntrEn is 0 and nFault transitions
4. When ackIntEn is 1 and the nAck signal
FIFO Operation
The FIFO threshold is set in the chip configuration
registers. All data transfers to or from the parallel
port can proceed in DMA or Programmed I/O
(non-DMA) mode as indicated by the selected
mode. The FIFO is used by selecting the Parallel
Port FIFO mode or ECP Parallel Port Mode. (FIFO
test mode will be addressed separately.) After a
reset, the FIFO is disabled. Each data byte is
transferred by a Programmed I/O cycle or PDRQ
depending
Programmed I/O mode.
The following paragraphs detail the operation of
the FIFO flow control.
<threshold> ranges from 1 to 16. The parameter
dmaEn is 1 and the DMA TC is received.
a.
b.(1) When serviceIntr is 0, dmaEn is 0,
from high to low or when nErrIntrEn is set from
1 to 0 and nFault is asserted.
transitions from a low to a high.
When serviceIntr is 0, dmaEn is 0,
direction
writeIntrThreshold or more free bytes in
the FIFO. Also, an interrupt is generated
when serviceIntr is cleared to 0 whenever
there are writeIntrThreshold or more free
bytes in the FIFO.
direction
readIntrThreshold or more bytes in the
FIFO.
when serviceIntr is cleared to 0 whenever
there are readIntrThreshold or more
bytes in the FIFO.
on
Also, an interrupt is generated
the
is
is
selection
0
1
In these descriptions,
and
and
of
there
there
DMA
are
are
or
104
FIFOTHR, which the user programs, is one less
and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer
periods of time between service requests, but
requires faster servicing of the request for both
read and write cases.
responsive to the service request.
desired case for use with a "fast" system. A high
value of threshold (i.e. 12) is used with a "sluggish"
system by affording a long latency period after a
service request, but results in more frequent
service requests.
DMA TRANSFERS
DMA transfers are always to or from the ecpDFifo,
tFifo or CFifo. DMA utilizes the standard PC DMA
services. To use the DMA transfers, the host first
sets up the direction and state as in the
programmed I/O case. Then it programs the DMA
controller in the host with the desired count and
memory address. Lastly it sets dmaEn to 1 and
serviceIntr to 0. The ECP requests DMA transfers
from the host by activating the PDRQ pin. The
DMA will empty or fill the FIFO using the
appropriate direction and mode.
terminal count in the DMA controller is reached, an
interrupt is generated and serviceIntr is asserted,
disabling DMA. In order to prevent possible
blocking of refresh requests dReq shall not be
asserted for more than 32 DMA cycles in a row.
The FIFO is enabled directly by asserting
nPDACK and addresses need not be valid. PINTR
is generated when a TC is received. PDRQ must
not be asserted for more than 32 DMA cycles in a
row. After the 32nd cycle, PDRQ must be kept
unasserted until nPDACK is deasserted for a
minimum of 350nsec. (Note: The only way to
properly terminate DMA transfers is with a TC.)
DMA may be disabled in the middle of a transfer
by first disabling the host DMA controller. Then
setting serviceIntr to 1, followed by setting dmaEn
to 0, and waiting for the FIFO to become empty or
full. Restarting the DMA is accomplished by
enabling DMA in the host, setting dmaEn to 1,
followed by setting serviceIntr to 0.
The host must be very
This is the
When the
Related parts for FDC37B72X_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN83C183-JD](/images/no-image3.png)
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N769TQFP](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47M102S-MC](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N267-MN](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![USB20H04-JD](/images/no-image3.png)
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37M602](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37B777](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37C672](/images/no-image3.png)
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
![COM90C66LJP](/images/no-image3.png)
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869TQFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![USB97C100QFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N227-MN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LAN91C94](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: