ADUC702X_1 AD [Analog Devices], ADUC702X_1 Datasheet - Page 29
![no-image](/images/no-image-200.jpg)
ADUC702X_1
Manufacturer Part Number
ADUC702X_1
Description
Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
Manufacturer
AD [Analog Devices]
Datasheet
1.ADUC702X_1.pdf
(78 pages)
Preliminary Technical Data
impedance source. Large source impedances will significantly
affect the AC performance of the ADC. This may necessitate
the use of an input buffer amplifier. The choice of the op amp
will be a function of the particular application.
When no amplifier is used to drive the analog input, the source
impedance should be limited to values lower than 1 kΩ
maximum source impedance will depend on the amount of
total harmonic distortion (THD) that can be tolerated. The
THD will increase as the source impedance increases and the
performance will degrade.
DRIVING THE ANALOG INPUTS
Internal or external reference can be used for the ADC. In
differential mode of operation, there are restrictions on
common mode input signal (V
reference value and supply voltage used to ensure that the signal
remains within the supply rails. Table 10 gives some calculated
V
ADC CALIBRATION
System calibration or device calibration are performed in
software. Two 10-bit registers are available for calibration,
AVDD
3.3V
3.0V
CM
min V
CM
VREF
2.5V
2.048V
1.25
2.5V
2.048V
1.25
max for some conditions.
Figure 15: Equivalent Analog Input Circuit
Conversion Phase: Switches Open
C1
C1
Track Phase: Switches Closed
Table 10: V
V
1.25V
1.024V
0.75V
1.25V
1.024V
0.75V
AV
AV
CM
D
D
D
D
DD
DD
min
CM
CM
ranges
) that are dependant on
R1 C2
R1 C2
V
2.05V
2.276V
2.55V
1.75V
1.976V
2.25V
CM
max
Signal
Peak-Peak
2.5V
2.048V
1.25
2.5V
2.048V
1.25
. The
Rev. PrA | Page 29 of 78
ADCOF and ADCGN.
For offset error correction, either an external pin must be tied to
AGND (system calibration) or the internal AGND channel
must be selected (device calibration). A software loop must be
implemented to tweak the value in ADCOF register each time
until the transition of ADCDAT reads code 0 to 1. Offset error
correction is done digitally and has a resolution of 0.25 lsb and
a range of +/- 3.125% of VREF.
For gain error correction, either an external pin must be tied to
VREF (system calibration) or the internal reference channel
must be selected (device calibration). A software loop must be
implemented to tweak the value in ADCGN register each time
until the transition of ADCDAT reads code 4094 to 4095.
Similar to the offset calibration, the gain calibration resolution
is 0.25 lsb with a range of +/- 3% of VREF.
TEMPERATURE SENSOR
The ADuC702x provides a voltage output from an on-chip
bandgap reference proportional to absolute temperature. It can
also be routed through the front end ADC multiplexer
(effectively an additional ADC channel input) facilitating an
internal
temperature to an accuracy of ±3°C.
BANDGAP REFERENCE
The ADuC702x provides an on-chip bandgap reference of 2.5V,
which can be used for the ADC and for the DAC. This internal
reference also appears on the V
reference, a capacitor of 0.47µF must be connected from the
external V
during ADC conversions. This reference can also be connected
to an external pin (VREF) and used as a reference for other
circuits in the system. An external buffer would be required
because of the low drive capability of the VREF output. A
programmable option also allows an external reference input on
the V
The bandgap reference interface consists on a 8-bit MMR,
REFCON described in
Table 11.
REF
pin.
REF
temperature
pin to AGND, to ensure stability and fast response
sensor
REF
pin. When using the internal
ADuC702x Series
channel,
measuring
die