A43L2632V-7 AMICC [AMIC Technology], A43L2632V-7 Datasheet - Page 15
![no-image](/images/no-image-200.jpg)
A43L2632V-7
Manufacturer Part Number
A43L2632V-7
Description
1M X 32 Bit X 4 Banks Synchronous DRAM
Manufacturer
AMICC [AMIC Technology]
Datasheet
1.A43L2632V-7.pdf
(43 pages)
Device Operations (continued)
Bank Activate
The bank activate command is used to select a random row
in an idle bank. By asserting low on RAS and
desired row and bank addresses, a row access is initiated.
The read or write operation can occur after a time delay of
t
internal timing parameter of SDRAM, therefore it is
dependent on operating clock frequency. The minimum
number of clock cycles required between bank activate and
read or write command should be calculated by dividing
t
the result to the next higher integer. The SDRAM has 4
internal banks on the same chip and shares part of the
internal circuitry to reduce chip area, therefore it restricts the
activation of all banks simultaneously. Also the noise
generated during sensing of each bank of SDRAM is high
requiring some time for power supplies to recover before the
other bank can be sensed reliably. t
minimum time required between activating different banks.
The number of clock cycles required between different bank
activation must be calculated similar to t
minimum time required for the bank to be active to initiate
sensing and restoring the complete row of dynamic cells is
determined by t
command to that active bank can be asserted. The maximum
time any bank can be in the active state is determined by
t
t
Burst Read
The burst read command is used to access burst of data on
consecutive clock cycles from an active row in an active
bank. The burst read command is issued by asserting low on
the clock. The bank must be active for at least t
before the burst read command is issued. The first output
appears CAS latency number of clock cycles after the issue
of burst read command. The burst length, burst sequence
and latency from the burst read command is determined by
the mode register which is already programmed. The burst
read can be initiated on any column address of the active
row. The address wraps around if the initial address does not
start from a boundary such that number of outputs from each
I/O are equal to the burst length programmed in the mode
register. The output goes into high-impedance at the end of
the burst, unless a new burst read was initiated to keep the
data output gapless. The burst read can be terminated by
issuing another burst read or burst write in the same bank or
the other active bank or a precharge command to the same
bank. The burst stop command is valid at every page burst
length.
Burst Write
The burst write command is similar to burst read command,
and is used to write data into the SDRAM consecutive clock
cycles in adjacent addresses depending on burst length and
burst sequence. By asserting low on
valid column address, a write burst is initiated. The data
inputs are provided for the initial address in the same clock
cycle as the burst write command. The input buffer is
deselected at the end of the burst length, even though the
PRELIMINARY
CS
RCD
RCD
RAS
RAS
(max). The number of cycles for both t
(max) can be calculated similar to t
(min) from the time of bank activation. t
(min) with cycle time of the clock and then rounding off
and
CAS
with
RAS
(January, 2005, Version 0.0)
(min) specification before a precharge
WE
being high on the positive edge of
CS
RCD
RRD
RCD
,
(min) specifies the
specification.
CAS
specification. The
RCD
and
RAS
(min) is an
(min) and
CS
WE
RCD
(min)
with
with
14
internal writing may not have been completed yet. The burst
write can be terminated by issuing a burst read and DQM for
blocking data inputs or burst write in the same or the other
active bank. The burst stop command is valid only at full
page burst length where the writing continues at the end of
burst and the burst is wrap around. The write burst can also
be terminated by using DQM for blocking data and
precharging the bank “t
written into the active row. See DQM OPERATION also.
DQM Operation
The DQM is used to mask input and output operation. It
works similar to
during write operation. The read latency is two cycles from
DQM and zero cycle for write, which means DQM masking
occurs two cycles later in the read cycle and occurs in the
same
synchronous with the clock, therefore the masking occurs for
a complete cycle. The DQM signal is important during burst
interrupts of write with read or precharge in the SDRAM. Due
to asynchronous nature of the internal write, the DQM
operation is critical to avoid unwanted or incomplete writes
when the complete burst write is not required.
Precharge
The precharge operation is performed on an active bank by
asserting low on
of the bank to be precharged. The precharge command can
be asserted anytime after t
activate command in the desired bank. “t
minimum time required to precharge a bank.
The minimum number of clock cycles required to complete
row precharge is calculated by dividing “t
time and rounding up to the next higher integer. Care should
be taken to make sure that burst write is completed or DQM
is used to inhibit writing before precharge command is
asserted. The maximum time any bank can be active is
specified by t
precharged
command. At the end of precharge, the bank enters the idle
state and is ready to be activated again.
Entry to Power Down, Auto refresh, Self refresh and Mode
register Set etc, is possible only when all banks are in idle
state.
Auto Precharge
The precharge operation can also be performed by using
auto precharge. The SDRAM internally generates the timing
to satisfy t
and CAS latency. The auto precharge command is issued at
the same time as burst read or burst write by asserting high
on A10/AP. If burst read or burst write command is issued
with low on A10/AP, the bank is left active until a new
command is asserted. Once auto precharge command is
given, no new commands are possible to that particular bank
until the bank achieves idle state.
cycle
RAS
(min) and “t
within
RAS
during
OE
CS
(max). Therefore, each bank has to be
during read operation and inhibits writing
,
t
RAS
RAS
write
RDL
RP
(max)
AMIC Technology, Corp.
RAS
” for the programmed burst length
” after the last data input to be
,
WE
(min) is satisfied from the bank
cycle.
from
and A10/AP with valid BA
DQM
the
RP
RP
” is defined as the
” with clock cycle
A43L2632
bank
operation
activate
is