DM9000BEP DAVICOM [Davicom Semiconductor, Inc.], DM9000BEP Datasheet - Page 38
![no-image](/images/no-image-200.jpg)
DM9000BEP
Manufacturer Part Number
DM9000BEP
Description
Ethernet Controller With General Processor Interface
Manufacturer
DAVICOM [Davicom Semiconductor, Inc.]
Datasheet
1.DM9000BEP.pdf
(56 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DM9000BEP
Manufacturer:
VISHAY
Quantity:
1 822
Part Number:
DM9000BEP
Manufacturer:
DAVICOM
Quantity:
20 000
9. Functional Description
9.1 Host Interface
The host interface is a general processor local bus
that using chip select (pin CS#) to access DM9000B.
Pin CS# is default low active which can be re-defined
by EEPROM setting.
There are only two addressing ports through the
access of the host interface. One port is the INDEX
port and the other is the DATA port. The INDEX port is
decoded by the pin CMD =0 and the DATA port by the
pin CMD =1. The contents of the INDEX port are the
register address of the DATA port. Before the access
of any register, the address of the register must be
saved in the INDEX port.
9.2 Direct Memory Access Control
The DM9000B provides DMA capability to simplify the
access of the internal memory. After the programming
of the starting address of the internal memory and
then issuing a dummy read/write command to load the
current data to internal data buffer, the desired
location of the internal memory can be accessed by
the read/write command registers. The memory’s
address will be increased with the size that equals to
the current operation mode (i.e. the 8-bit or 16-bit
mode) and the data of the next location will be loaded
into internal data buffer automatically. It is noted that
the data of the first access (the dummy read/write
command) in a sequential burst should be ignored
because that the data was the contents of the last
read/write command.
The internal memory size is 16K bytes. The first
location of 3K bytes is used for the data buffer of the
packet transmission. The other 13K bytes are used for
the buffer of the receiving packets. So in the write
memory operation, when the bit 7 of IMR is set, the
memory address increment will wrap to location 0 if
the end of address (i.e. 3K) is reached. In a similar
way, in the read memory operation, when the bit 7 of
Final
Version: DM9000B-13-DS-F02
June 4, 2009
Ethernet Controller with General Processor Interface
IMR is set, the memory address increment will wrap to
location 0x0C00 if the end of address (i.e. 16K) is
reached.
9.3 Packet Transmission
There are two packets, sequentially named as index I
and index II, can be stored in the TX SRAM at the
same time. The index register 02h controls the
insertion of CRC and pads. Their statuses are
recorded at index registers 03h and 04h respectively.
The start address of transmission is 00h and the
current packet is index I after software or hardware
reset. Firstly write data to the TX SRAM using the
DMA port and then write the byte count to byte_ count
register at index register 0fch and 0fdh. Set the bit 1 of
control register. The DM9000B starts to transmit the
index I packet. Before the transmission of the index I
packet ends, the data of the next (index II) packet can
be moved to TX SRAM. After the index I packet ends
the transmission, write the byte count data of the
index II to BYTE_COUNT register and then set the bit
1 of control register to transmit the index II packet.
The following packets, named index I, II, I, II,…, use
the same way to be transmitted.
9.4 Packet Reception
The RX SRAM is a ring data structure. The start
address of RX SRAM is 0C00h after software or
hardware reset. Each packet has a 4-byte header
followed with the data of the reception packet which
CRC field is included. The format of the 4-byte header
is
BYTE_COUNT high. It is noted that the start address
of each packet is in the proper address boundary
which depends on the operation mode (the 8-bit or
16-bit ).
01h,
status,
BYTE_COUNT
DM9000B
low,
and
38