IS42S32800B-7TL ISSI, Integrated Silicon Solution Inc, IS42S32800B-7TL Datasheet - Page 18
![IC SDRAM 256MBIT 143MHZ 86TSOP](/photos/7/23/72336/is42s32800b-7tl_sml.jpg)
IS42S32800B-7TL
Manufacturer Part Number
IS42S32800B-7TL
Description
IC SDRAM 256MBIT 143MHZ 86TSOP
Manufacturer
ISSI, Integrated Silicon Solution Inc
Datasheet
1.IS42S32800B-7BL.pdf
(62 pages)
Specifications of IS42S32800B-7TL
Package / Case
86-TSOPII
Memory Size
256M (8Mx32)
Format - Memory
RAM
Memory Type
SDRAM
Speed
143MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Data Bus Width
32 bit
Organization
2 Mbit x 32
Maximum Clock Frequency
143 MHz
Access Time
7 ns
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3 V
Maximum Operating Current
150 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
706-1025
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IS42S32800B-7TL
Manufacturer:
ISSI
Quantity:
1 000
Part Number:
IS42S32800B-7TL
Manufacturer:
ISSI
Quantity:
20 000
Company:
Part Number:
IS42S32800B-7TLI
Manufacturer:
ISSI
Quantity:
1 000
I
IS42S32800B
18
•
•
This bit is used to select the burst write length.
8
9
Test Mode field (A8~A7)
These two bits are used to enter the test mode and must be programmed to “00”in normal operation.
Write Burst Length (A9)
No-Operation command
(RAS#=”H”,CAS#=”H”,WE#=”H”)
is Low).This prevents unwanted commands from being registered during idle or wait states.
Burst Stop command
(RAS#=”H”,CAS#=”H”,WE#=”L”)
The Burst Stop command is used to terminate either fixed-length or full-page bursts.This
command is only effective in a read/write burst without the auto precharge function.The terminated
read burst ends after a delay equal to the CAS#latency (refer to the following figure).The
termination of a write burst is shown in the following figure.
CL K
COMMAN D
CAS# latency=2,3
DQ’s
CLK
COMMAND
CAS# latency=2
tCK2,DQ’s
CAS# latency=3
tCK3,DQ’s
Termination of a Burst Read Operation (Burst Length > 4,CAS#Latency =2,3)
A9
0
1
A8
0
0
1
The No-Operation command is used to perform a NOP to the SDRAM which is selected (CS#
READ A
T0
T0
Termination of a Burst Write Operation (Burst Length =X)
NOP
Write Burst Length
Burst
Single Bit
A7
0
1
X
WRITE A
DIN A 0
T 1
T 1
NOP
Test Mode
normal mode
Vendor Use Only
Vendor Use Only
DOUT A 0
DIN A 1
T2
NOP
T2
NOP
DOUT A 0
DOUT A 1
DIN A 2
T3
NOP
T3
NOP
Input Data for the Write is masked.
Burst Stop
Burst Stop
don’t care
DOUT A 2
DOUT A 1
T4
T4
DOUT A 2
DOUT A 3
T5
NOP
The Burst ends after a delay equal to the CAS# latency.
T5
NOP
DOUT A 3
T6
NOP
T6
NOP
Integrated Silicon Solution, Inc.
T7
NOP
T7
NOP
I
NOP
T 8
NOP
T 8
07/21/09
Rev. F
®