ISPPAC-POWR1208-01T44E Lattice, ISPPAC-POWR1208-01T44E Datasheet - Page 26
![no-image](/images/manufacturer_photos/0/3/380/lattice_sml.jpg)
ISPPAC-POWR1208-01T44E
Manufacturer Part Number
ISPPAC-POWR1208-01T44E
Description
Supervisory Circuits PROGRAMMABLE PWR SUPPLY CONTR
Manufacturer
Lattice
Datasheet
1.ISPPAC-POWR1208-01T44I.pdf
(34 pages)
Specifications of ISPPAC-POWR1208-01T44E
Number Of Voltages Monitored
12
Monitored Voltage
Adjustable
Undervoltage Threshold
1.03 V
Overvoltage Threshold
5.72 V
Manual Reset
Not Resettable
Watchdog
No Watchdog
Supply Voltage - Max
5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Package / Case
TQFP-100
Minimum Operating Temperature
- 40 C
Factory Pack Quantity
800
Supply Current (typ)
15000 uA
Supply Voltage - Min
2.25 V
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISPPAC-POWR1208-01T44E
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Lattice Semiconductor
Figure 15. UES Register
PROGUES – This instruction will program the content of the UES Register into the UES E
device must already be in programming mode (PROGRAMEN instruction). This instruction also forces the outputs
into the SAFESTATE.
Notes:
In all of the descriptions above, SAFESTATE refers both to the instruction and the state of the digital output pins, in
which the open-drains are tri-stated and the FET drivers are pulled low.
Before any of the above programming instructions are executed, the respective E
using the corresponding erase instruction.
Application Example
The ispPAC-POWR1208 device has 12 comparators to monitor various power supply levels. The comparators each
have a programmable trip point that is programmed by the user at design time. The output of the comparators feed
into the PLD logic array to drive the state machine logic or monitor logic. The outputs of comparators
COMP1...COMP8 are also routed to external pins to be monitored directly or can be used to drive additional control
logic if expansion is required. The comparator outputs are open-drain type output buffers and require a pull up
resistor to drive a logic high. All 12 comparators have hysteresis, the hysteresis is dependent on the voltage trip
point scale that is set, it ranges from 3.4mV for the 1.2V monitor supply range to 16.2mV for the 5.0V monitor sup-
ply range. The comparators can be set with a trip point from 1.03V to 5.72V, with 192 different values. The applica-
tion diagram shows a set-up that can monitor and control multiple power supplies. The ispPAC-POWR1208 device
controls FET switches to ramp the supplies at different slew rates and time delays. The digital outputs and inputs
are also used to interface with the board that is being powered up.
To reduce the possibility of RF oscillation, a gate resistor (R
FET power switch. This resistor should be placed physically close to the MOSFET gate terminal, and connected by
as short a PCB trace as is feasible. An appropriate value for these gate resistors is highly dependent on both the
characteristics of the MOSFET being used and the circumstances of the application, but will often be in the range
of 10Ω to 100Ω.
Bit
15
Bit
14
Bit
13
Bit
12
Bit
11
Bit
10
Bit
9
Bit
8
26
Bit
7
G
) is often inserted in series with the gate of the MOS-
Bit
6
Bit
5
ispPAC-POWR1208 Data Sheet
Bit
4
2
Bit
3
CMOS bits need to be erased
Bit
2
2
CMOS memory. The
Bit
1
Bit
0
TDO