M25PE16-VMW6TG NUMONYX, M25PE16-VMW6TG Datasheet - Page 31
![IC FLASH 16MBIT 75MHZ 8SOIC](/photos/7/28/72835/m25pe16-vmw6tg_sml.jpg)
M25PE16-VMW6TG
Manufacturer Part Number
M25PE16-VMW6TG
Description
IC FLASH 16MBIT 75MHZ 8SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M45PE16-VMP6TG.pdf
(58 pages)
Specifications of M25PE16-VMW6TG
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
16M (2M x 8)
Speed
75MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
Package
8SOIC W
Cell Type
NOR
Density
16 Mb
Architecture
Sectored
Block Organization
Symmetrical
Typical Operating Supply Voltage
3.3 V
Sector Size
64KByte x 32
Timing Type
Synchronous
Interface Type
Serial-SPI
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M25PE16-VMW6TGTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25PE16-VMW6TG
Manufacturer:
MAXIM
Quantity:
14 500
Company:
Part Number:
M25PE16-VMW6TG
Manufacturer:
Numonyx
Quantity:
15 000
Part Number:
M25PE16-VMW6TG
Manufacturer:
ST
Quantity:
20 000
M25PE16
6.8
Read lock register (RDLR)
The device is first selected by driving Chip Select (S) Low. The instruction code for the read
lock register (RDLR) instruction is followed by a 3-byte address (A23-A0) pointing to any
location inside the concerned sector. Each address bit is latched-in during the rising edge of
Serial Clock (C). Then the value of the lock register is shifted out on serial data output (Q),
each bit being shifted out, at a maximum frequency f
(C).
The instruction sequence is shown in
The read lock register (RDLR) instruction is terminated by driving Chip Select (S) High at
any time during data output.
Any read lock register (RDLR) instruction, while an erase, program or write cycle is in
progress, is rejected without having any effects on the cycle that is in progress.
Table 9.
Figure 13. Read lock register (RDLR) instruction sequence
b7-b2
S
C
D
Q
Bit
b1
b0
Sector lock down
Sector write lock
0
Lock register out
and data-out sequence
Bit name
1
High Impedance
2
Instruction
3
4
5
Value
‘1’
‘0’
‘1’
‘0’
6
7
MSB
The write lock and lock down bits cannot be changed. Once a
‘1’ is written to the lock down bit it cannot be cleared to ‘0’,
except by a reset or power-up.
The write lock and lock down bits can be changed by writing
new values to them (default value).
Write, program and erase operations in this sector will not be
executed. The memory contents will not be changed.
Write, program and erase operations in this sector are
executed and will modify the sector contents (default value).
23
8
22 21
Figure
9 10
24-bit address
13.
Reserved
3
28 29 30 31 32 33 34 35
2
C
1
, during the falling edge of Serial Clock
0
MSB
Function
7
6
Lock register out
5
4
3
36 37 38
2
1
Instructions
0
39
AI10783
31/58