CAT28F010G12 ON Semiconductor, CAT28F010G12 Datasheet
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT28F010G12
Specifications of CAT28F010G12
CAT28F010G-12
Available stocks
Related parts for CAT28F010G12
CAT28F010G12 Summary of contents
Page 1
... The CAT28F010 is a high speed 128K x 8-bit electrically erasable and reprogrammable Flash memory ideally suited for applications requiring in-system or after-sale code updates. Electrical erasure of the full memory contents is achieved typically within 0.5 second pin and Read timing compatible with standard EPROM and EEPROM devices. Programming and Erase are performed through an operation and verify algorithm ...
Page 2
... Pin Name A I I/O 7 TSOP Package (Reverse Pinout) (TR, HR) 2 Type Function –A Input Address Inputs for 0 16 memory addressing –I/O I/O Data Input/Output 0 7 Input Chip Enable Input Output Enable Input Write Enable Voltage Supply CC Ground SS Program/Erase PP Voltage Supply ...
Page 3
ABSOLUTE MAXIMUM RATINGS* Temperature Under Bias .................. - +130 C Storage Temperature ........................ - +150 C Voltage on Any Pin with (1) Respect to Ground ............ -2. Voltage on Pin A with 9 (1) ...
Page 4
CAT28F010 D.C. OPERATING CHARACTERISTICS V = +5V 10%, unless otherwise specified. CC Symbol Parameter I Input Leakage Current LI I Output Leakage Current Standby Current CMOS SB1 Standby Current TTL SB2 ...
Page 5
SUPPLY CHARACTERISTICS Symbol V V Supply Voltage During Read Operations PPL During Read/Erase/Program PPH PP A.C. CHARACTERISTICS, Read Operation V = +5V 10%, unless otherwise specified. CC JEDEC Standard Symbol Symbol Parameter t ...
Page 6
CAT28F010 A.C. CHARACTERISTICS, Program/Erase Operation V = +5V 10%, unless otherwise specified. CC \JEDEC Standard Symbol Symbol Parameter t t Write Cycle Time AVAV Address Setup Time AVWL Address Hold Time WLAX AH t ...
Page 7
FUNCTION TABLE Mode CE Read V IL Output Disable V IL Standby V IH Signature (MFG Signature (Device Program/Erase V IL Write Cycle V IL Read Cycle V IL WRITE COMMAND TABLE Commands are written ...
Page 8
... PP be sent before reading data (see Write Operations). The data retrieved from the I/O pins reflects the contents of the memory location corresponding to the state of the 17 address pins. The respective timing waveforms for the read operation are shown in Figure 3. Refer to the AC Read characteristics for specific timing parameters. ...
Page 9
WRITE OPERATIONS The following operations are initiated by observing the sequence specified in the Write Command Table. Read Mode The device can be put into a standard READ mode by initiating a write cycle with 00H on the data bus. ...
Page 10
CAT28F010 (1) Figure 5. Chip Erase Algorithm START ERASURE APPLY V PPH PROGRAM ALL BYTES TO 00H INITIALIZE ADDRESS INITIALIZE PLSCNT = 0 WRITE ERASE SETUP COMMAND WRITE ERASE COMMAND TIME OUT 10ms WRITE ERASE VERIFY COMMAND TIME OUT 6 ...
Page 11
... Figure 7. During the first write cycle, the command 40H is written into the command register. During the second write cycle, the address of the memory location to be programmed is latched on the falling edge of WE, while the data is latched on the rising edge of WE. The program operation terminates with the next rising edge of WE ...
Page 12
CAT28F010 Figure 7. Programming Algorithm START PROGRAMMING APPLY V PPH INITIALIZE ADDRESS PLSCNT = 0 WRITE SETUP PROG. COMMAND WRITE PROG. CMD ADDR AND DATA TIME OUT 10 s WRITE PROGRAM VERIFY COMMAND TIME OUT 6 s READ DATA FROM ...
Page 13
Program-Verify Mode A Program-verify cycle is performed to ensure that all bits have been correctly programmed following each byte programming operation. The specific address is already latched from the write cycle just completed, and stays latched until the verify is ...
Page 14
CAT28F010 A.C. CHARACTERISTICS, Read Operation V = +5V 10%, unless otherwise specified. CC JEDEC Standard Symbol Symbol Parameter t t Write Cycle Time AVAV Address Setup Time AVEL Address Hold Time ELAX AH t ...
Page 15
EXAMPLE OF ORDERING INFORMATION Prefix Device # CAT 28F010 Product Number Optional Company ID ORDERING INFORMATION ...
Page 16
... D Added Green Packages in all areas. 15-Oct-08 E Eliminate PDIP SnPb package. 17-Nov-08 F Change logo and fine print to ON Semiconductor 31-Jul-09 G Update Absolute Maximum Ratings Update Example of Ordering Information Update Ordering Information table ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein ...