IRS26310DJPBF International Rectifier, IRS26310DJPBF Datasheet - Page 32

• Manufacturer Part Number: IRS26310DJPBF
• Description: IC DRIVER BRIDGE 3-PHASE 44-PLCC
• Manufacturer: International Rectifier

Specifications of IRS26310DJPBF

• Configuration: 3 Phase Bridge
• Input Type: Non-Inverting
• Delay Time: 530ns
• Current - Peak: 200mA
• Number Of Configurations: 1
• Number Of Outputs: 3
• High Side Voltage - Max (bootstrap): 600V
• Voltage - Supply: 12 V ~ 20 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 44-PLCC (32 Leads)
• Peak Output Current: 200mA
• Input Delay: 530ns
• Output Delay: 530ns
• Supply Voltage Range: 12V To 20V
• Driver Case Style: LCC
• No. Of Pins: 44
• Operating Temperature Range: -40°C To +125°C
• Rohs Compliant: Yes
• Device Type: High Side / Low Side
• Family Hvic: General Purpose HVICs
• Channels: 6
• Topology: Three Phase
• Application: General Purpose / Motor Control / PDP
• Voffset: 600
• Io+ (ma): 200
• Io- (ma): 350
• Shutdown / Reset: Yes
• Separate Power And Logic Ground: Yes
• Integrated Bootstrap Diode: Yes
• Over Current Protection: Yes
• Uvlo: Vcc / Vbs
• Vbsuv+ / Vccuv+ Min (v): 10.4
• Vbsuv+ / Vccuv+ Typ (v): 11.1
• Vbsuv+ / Vccuv+ Max (v): 11.6
• Vbsuv- / Vccuv- Min (v): 10.2
• Vbsuv- / Vccuv- Typ (v): 10.9
• Dt / Sdt Min (ns): 190
• Dt / Sdt Typ (ns): 290
• Dt / Sdt Max (ns): 420
• T On Min (ns): 400
• T On Typ (ns): 530
• T On Max (ns): 750
• T Off Min (ns): 400
• T Off Typ (ns): 530
• T Off Max (ns): 750
• Fault Reporting: Yes
• Package: 44 Lead
• Part Status: Active & Preferred
• Special Features: DC Bus Sensing with Over Voltage Protection
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

IRS26310DJPbF
Figure 33: Negative V
transient results for an International Rectifier HVIC
S
Even though the IRS26310D has been shown able to handle these large negative V
transient conditions, it is highly
S
recommended that the circuit designer always limit the negative V
transients as much as possible by careful PCB
S
layout and component use.
PCB Layout Tips
Distance between high and low voltage components: It’s strongly recommended to place the components tied to the
floating voltage pins (V
and V
) near the respective high voltage portions of the device. The IRS26310D in the
B
S
PLCC44 package has had some unused pins removed in order to maximize the distance between the high voltage
and low voltage pins. Please see the Case Outline PLCC44 information in this datasheet for the details.
Ground Plane: In order to minimize noise coupling, the ground plane should not be placed under or near the high
voltage floating side.
Gate Drive Loops: Current loops behave like antennas and are able to receive and transmit EM noise (see Figure
34). In order to reduce the EM coupling and improve the power switch turn on/off performance, the gate drive loops
must be reduced as much as possible. Moreover, current can be injected inside the gate drive loop via the IGBT
collector-to-gate parasitic capacitance. The parasitic auto-inductance of the gate loop contributes to developing a
voltage across the gate-emitter, thus increasing the possibility of a self turn-on effect.
Figure 34: Antenna Loops
www.irf.com
© 2008 International Rectifier
32