LM8333EVALKIT National Semiconductor, LM8333EVALKIT Datasheet - Page 15

• Manufacturer Part Number: LM8333EVALKIT
• Description: BOARD EVALUATION LM8333
• Manufacturer: National Semiconductor

Specifications of LM8333EVALKIT

• Main Purpose: Interface, Special Purpose
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: LM8333
• Primary Attributes: Mobile I/O Companion with Key-Scan, I/O Expansion, PWM, Access.bus Host
• Secondary Attributes: Board has MCU for USB to PC GUI
• Lead Free Status / RoHS Status: Not applicable / Not applicable

V
I
I
V
V
C
DD
HALT
Symbol
CC
IL
IH
PAD
11.0 Absolute Maximum Ratings
1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
12.0 DC Electrical Characteristics
(Temperature: -40°C
Data sheet specification limits are guaranteed by design, test, or statistical analysis.
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics tables.
Note 2: Data sheet minimum and maximum limits are guaranteed by design, test, or statistical analysis.
Note 3: Supply current is measured with inputs connected to V
Note 4: T
Note 5: In Halt mode, the internal clock is switched off. Supply current in Halt mode is measured with inputs connected to V
connected to a load.
Note 6: Guaranteed by design, not tested.
Supply Voltage (V
Voltage at Any Pin
Maximum Input Current Without
Latchup
C
Operating Voltage
Power Supply Rise Time from 0.0V
(On Chip Power-On Reset Selected)
Supply Current
Standby Mode Current
Logical 0 Input Voltage
Logical 1 Input Voltage
Hi-Z Input Leakage (TRI-STATE Output)
Input PullupCurrent
Port Input Hysteresis
Output Current Source (Weak Pull-Up)
Output Current Source (Push-Pull Mode)
Output CurrentSink (Push-Pull Mode)
Allowable Sink and Source Current per Pin
Input Capacitance
= instruction cycle time (min. 0.7 µs).
CC
≤
)
TA
(Note
Parameter
≤
+85°C)
(Note
3)
(Note
6)
5)
-0.3V to VCC +0.3V
±100 mA
CC
and outputs driven low but not connected to a load.
3.5V
(Note
RC Clock = 10 MHz,
V
4)
V
4), T
V
V
V
V
V
CC
CC
CC
CC
CC
CC
CC
= 2.75V, T
= 2.75V, T
= 2.75V
= 2.75V, V
= 2.25V, V
= 2.25V, V
= 2.25V, V
A
15
= 25°C
Conditions
ESD Protection Level
Human Body Model
Machine Model
Total Current into VCC Pin
(Source)
Total Current out of GND Pin (Sink)
Storage Temperature Range
C
C
IN
OH
OH
OL
= 1 µs
= 0 µs,
= 0V
= 0.4V
= 1.7V
= 1.7V
(Note
(Note
(Note
0.8 V
20 µs
2.25
Min
-0.1
-15
0.1
-10
-10
10
CC
2)
CC
and outputs driven low but not
Typ
<2
−65°C to +140°C
0.25 V
(Note
10 ms
Max
-120
2.9
0.1
-80
8.5
15
16
6
www.national.com
2)
CC
80 mA
60 mA
200V
2 kV
Units
mA
mA
mA
mA
µA
µA
µA
µA
pF
V
V
V
V