OM11048 NXP Semiconductors, OM11048 Datasheet - Page 31

• Manufacturer Part Number: OM11048
• Description: BOARD LPCXPRESSO LPC1343
• Manufacturer: NXP Semiconductors
• Series: LPCXpressor
• Type: MCUr

Specifications of OM11048

• Contents: Board, Software
• Processor To Be Evaluated: LPC1343
• Processor Series: LPC13xx
• Interface Type: USB, I2C, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 3.3 V
• Tool Type: Demonstration Board
• Core Architecture: ARM
• Cpu Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: LPC1343
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4947

NXP Semiconductors
Table 7.
T
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] Including voltage on outputs in 3-state mode.
[11] V
[12] 3-state outputs go into 3-state mode in Deep power-down mode.
[13] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[14] To V
[15] Includes external resistors of 33 Ω ± 1 % on USB_DP and USB_DM.
Table 8.
T
LPC1311_13_42_43
Product data sheet
Symbol
V
C
E
E
E
E
Symbol Parameter
V
V
V
V
V
V
C
Z
amb
amb
DRV
BUS
DI
CM
th(rs)se
OL
OH
IA
D
L(adj)
O
G
trans
ia
Typical ratings are not guaranteed. The values listed are at room temperature (25 °C), nominal supply voltages.
IRC enabled; system oscillator disabled; system PLL disabled.
I
BOD disabled.
All peripherals disabled in the SYSAHBCLKCTRL register. Peripheral clocks to UART, SSP, trace clock, and SysTick timer disabled in
the syscon block.
For LPC134x: USB_DP and USB_DM pulled LOW externally.
IRC disabled; system oscillator enabled; system PLL enabled.
All oscillators and analog blocks turned off in the PDSLEEPCFG register; PDSLEEPCFG = 0x0000 0FFF.
WAKEUP pin pulled HIGH externally.
DD
= −40 °C to +85 °C, unless otherwise specified.
= −40 °C to +85 °C unless otherwise specified; ADC frequency 4.5 MHz, V
DD
measurements were performed with all pins configured as GPIO outputs driven LOW and pull-up resistors disabled.
SS
supply voltage must be present.
.
bus supply voltage
differential input
sensitivity voltage
differential common
mode voltage range
single-ended receiver
switching threshold
voltage
LOW-level output
voltage
HIGH-level output
voltage
transceiver capacitance pin to GND
driver output
impedance for driver
which is not high-speed
capable
Static characteristics
ADC static characteristics
Parameter
analog input voltage
analog input capacitance
differential linearity error
integral non-linearity
offset error
gain error
…continued
Conditions
|(D+) − (D−)|
includes V
for low-/full-speed;
R
driven; for low-/full-speed;
R
with 33 Ω series resistor; steady state
drive
L
L
of 1.5 kΩ to 3.6 V
of 15 kΩ to GND
All information provided in this document is subject to legal disclaimers.
Conditions
DI
range
Rev. 3 — 10 August 2010
[1][2]
[3]
[4]
[5]
Min
0
-
-
-
-
-
[15]
32-bit ARM Cortex-M3 microcontroller
DD
LPC1311/13/42/43
= 2.5 V to 3.6 V.
Min
-
0.2
0.8
0.8
-
2.8
-
36
Typ
-
-
-
-
-
-
Typ
-
-
-
-
-
-
-
-
[1]
Max
V
1
±1
±1.5
±3.5
0.6
© NXP B.V. 2010. All rights reserved.
DD
Max
5.25
-
2.5
2.0
0.18
3.5
20
44.1
Unit
V
pF
LSB
LSB
LSB
%
31 of 62
Unit
V
V
V
V
V
V
pF
Ω