HW-V5-ML501-UNI-G Xilinx Inc, HW-V5-ML501-UNI-G Datasheet - Page 29
![EVALUATION PLATFORM VIRTEX-5](/photos/9/24/92456/hw-v5-ml501-uni-g_sml.jpg)
HW-V5-ML501-UNI-G
Manufacturer Part Number
HW-V5-ML501-UNI-G
Description
EVALUATION PLATFORM VIRTEX-5
Manufacturer
Xilinx Inc
Series
Virtex™-5 LXr
Type
FPGAr
Datasheet
1.HW-V5-ML501-UNI-G.pdf
(42 pages)
Specifications of HW-V5-ML501-UNI-G
Design Resources
ML501 Ref Design User Guide ML501 Schematics
Contents
ML501 Platform, DVI Adapter and CompactFlash Card
Silicon Manufacturer
Xilinx
Features
Programmable System Clock Generator Chip, RS-232 Serial Port
Silicon Family Name
Virtex-5
Silicon Core Number
XC5VLX50FFG676
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
XC5VLX50FFG676
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
122-1508
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Table 1-13: Board Connections for PHY Configuration Pins
ML501 Evaluation Platform
UG226 (v1.4) August 24, 2009
Config Pin
CONFIG0
CONFIG1
CONFIG2
CONFIG3
CONFIG4
CONFIG5
CONFIG6
22. USB Controller with Host and Peripheral Ports
R
Connection on
V
LED_DUPLEX
(Set by J40)
CC
V
V
V
V
LED_RX
Ground
Board
CC
CC
CC
CC
2.5V or
2.5V
2.5V
2.5V
2.5V
settings (See
whether the PHY defaults to RGMII mode (pin 2-3) or GMII mode (pin 1-2).
A Cypress CY7C67300 embedded USB host controller provides USB connectivity for the
board. The USB controller supports host and peripheral modes of operation. The USB
controller has two serial interface engines (SIE) that can be used independently. SIE1 is
connected to the USB Host connector (P19). SIE2 is connected only to the USB Peripheral
connector (P17).
The USB controller has an internal microprocessor to assist in processing USB commands.
The firmware for this processor can be stored in its own dedicated IIC EEPROM (U28) or
can be downloaded from a host computer via a peripheral connector. The USB controller's
serial port is connected to J30 through an RS-232 transceiver to assist with debug. Jumper
J50 can be installed to prevent the USB controller from executing firmware stored in the IIC
EEPROM.
PHYADR[2] = 1
ENA_PAUSE = 0
ANEG[3] = 1
ANEG[0] = 1
HWCFG_MODE[2] = 0 or 1
(Set by J40)
DIS_FC = 1
SEL_BDT = 0
Definition and Value
Table
Bit[2]
1-13). These settings can be overwritten via software. Jumper J40 selects
www.xilinx.com
PHYADR[1] = 1
PHYADR[4] = 0
HWCFG_MODE[1] = 1
INT_POL = 1
ANEG[2] = 1
ENA_XC = 1
DIS_SLEEP = 1
Definition and Value
Bit[1]
PHYADR[0] = 1
PHYADR[3] = 0
ANEG[1] = 1
DIS_125 = 1
HWCFG_MODE[0] = 1
HWCFG_MODE[3] = 1
75/50Ω = 0
Definition and Value
Detailed Description
Bit[0]
29