101-1017 Rabbit Semiconductor, 101-1017 Datasheet - Page 214
101-1017
Manufacturer Part Number
101-1017
Description
KIT DEV POWERCORE 3800 INT'L
Manufacturer
Rabbit Semiconductor
Series
PowerCore FLEXr
Type
MPU Moduler
Datasheet
1.101-1007.pdf
(240 pages)
Specifications of 101-1017
Contents
RabbitCore Module, Dev. Board, AC Adapter, Cable and Dynamic C® CD-Rom
Processor To Be Evaluated
PowerCore 38xx
Interface Type
Ethernet
For Use With/related Products
RCM3800
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 214 of 240
- Download datasheet (3Mb)
Option 5—Half-Wave Rectifier
Option 5 requires unregulated AC or DC. This option places a half-wave rectifier and fil-
ter before the regulators. The half-wave rectifier is necessary to rectify AC voltage into
DC voltage. This option has a friction lock connector installed on the PowerCore to accept
external power.
The half-wave rectifier causes a 0.7 V voltage drop before voltage is applied to the regula-
tors. This means that the 0.7 V drop will need to be taken into account.
With this option, unregulated DC voltage is input to pin 2 of friction lock connector J3.
The negative side of the input voltage is applied to pin 4 and/or 6 of friction lock connec-
tor J3. The selection of the +5 V regulator determines the voltage range for the unregu-
lated DC input power as follows.
• 8–43 V DC for 2 A regulator option
• 9–40 V DC for 1 A regulator option
AC voltage is applied to the same pins of J3. Because the peak AC voltages are 1.42 times
higher than the rated AC voltages, the AC voltage applied will have lower upper limits.
Also, because AC voltage inputs go down to zero voltage during each cycle, a higher min-
imum voltage than the DC voltage will be required. The selection of the +5 V regulator
determines the voltage range for the AC input power as follows.
• 17–30 V AC for 2 A regulator option
• 14–28 V AC for 1 A regulator option
The current required is calculated based on the power consumed by the PowerCore as
optionally configured: I = Power/Vin. The PowerCore will consume between 1 W and 2.7 W,
depending on the PowerCore options. Additional power may be needed to provide for
other user's circuitry external to the PowerCore. That additional power needed from the
input power supply is calculated as follows.
• For the user's 5 V circuitry, additional power from supply =
• For the user's 3.45 V circuitry, additional power from supply =
Additional power is taken by the input diodes.
Thus, as an example, if the user's 5 V circuitry consumes 2.5 W and the user's 3.45 V cir-
cuitry consumes 0.5 W, the total power needed from the power supply is (2.5 W × 1.33 +
0.5 W × 1.92 + (PowerCore consumption as optionally configured)) = 5.3 W to 7.0 W. If
the external power supply is a 24 V supply, then it will need to source I = Power/Voltage
current. Bear in mind that voltage presented to the regulators has a 0.7 V diode drop. Thus
the voltage in this formula must be reduced by 0.7 V, so current = Power/23.3 V = 5.3 W/
23.3 V = 227 mA; 7.0 W/23.3 V = 300 mA. An AC supply may not need to deliver that
much current because the filter capacitor may raise the DC voltage input into the regulator,
allowing less current to be consumed. For a 24 V DC input, this is what current the power
supply would need to deliver.
206
(5Vpower_to_user's_circuit) × 1.33.
(3.45Vpower_to_user's_circuit) × 1.92.
PowerCore FLEX
Related parts for 101-1017
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT DEV STANDARD RCM5700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV FOR BL2500 COYOTE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories Keypad/Display Unit 5V Panel Mount
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
Single Board Computers 24VDC/110 Power Supp
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor