101-0530 Rabbit Semiconductor, 101-0530 Datasheet - Page 18
101-0530
Manufacturer Part Number
101-0530
Description
KIT TOOL FOR LP3500 INTL
Manufacturer
Rabbit Semiconductor
Series
RabbitCore 3000r
Type
Single Board Computers (SBC)r
Datasheet
1.20-101-0525.pdf
(142 pages)
Specifications of 101-0530
Contents
Demo Board, Serial Cable, Software and Documentation
For Use With/related Products
Rabbit 3000-based products, except RCM30/3100, LP3500
Lead Free Status / RoHS Status
Vendor undefined / Vendor undefined
- Current page: 18 of 142
- Download datasheet (4Mb)
4. Connect the power supply.
First, prepare the AC adapter for the country where it will be used by selecting the plug.
The LP3500 Tool Kit presently includes Canada/Japan/U.S., Australia/N.Z., U.K., and
European style plugs. Snap in the top of the plug assembly into the slot at the top of the
AC adapter as shown in Figure 4, then press down on the spring-loaded clip below the
plug assembly to allow the plug assembly to click into place.
Hook up the connector from the wall transformer to header J5 on the Prototyping Board as
shown in Figure 4. The orientation of this connector is not important since the VIN (posi-
tive) voltage is the middle pin, and GND is available on both ends of the three-pin header
J5.
5. Apply power.
Plug in the AC adapter. If you are using your own power supply, it must provide 3 V to
30 V DC—voltages outside this range could damage the LP3500.
Reset switches are located on both sides of the LP3500 board.
12
NOTE: Do not connect the AC adapter to the VBAT terminal on the Prototyping Board.
NOTE: A hardware reset may be done by pressing the RESET switch on the LP3500.
The VBAT terminal supplies the backup battery voltage of 3 V, and the LP3500 may be
damaged if subjected to the raw DC voltage from the AC adapter through the VBAT
terminal.
The LP3500 may also be reset by unplugging the AC adapter, then plugging it back in.
However, when the LP3500 is operating in the power-save mode, the backup battery
will provide sufficient voltage to prevent a reset from happening, in which case you will
have to press the RESET switch on the LP3500.
Figure 5. Locations of LP3500 RESET Switches
Fox (LP3500)
Related parts for 101-0530
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SNGLBD BL2101 A/D 0-10V
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
CARD D/A 0-10V SR9400 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
CARD A/D 0-10V SR9300 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools WIRELESS CONTROL APP KIT
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
KIT DEV RABBITCORE RCM3750
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV RABBIT 2000 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV RABBIT RCM2000 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEVELOPMENT RCM3700 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor