101-0530 Rabbit Semiconductor, 101-0530 Datasheet - Page 27
101-0530
Manufacturer Part Number
101-0530
Description
KIT TOOL FOR LP3500 INTL
Manufacturer
Rabbit Semiconductor
Series
RabbitCore 3000r
Type
Single Board Computers (SBC)r
Datasheet
1.20-101-0525.pdf
(142 pages)
Specifications of 101-0530
Contents
Demo Board, Serial Cable, Software and Documentation
For Use With/related Products
Rabbit 3000-based products, except RCM30/3100, LP3500
Lead Free Status / RoHS Status
Vendor undefined / Vendor undefined
- Current page: 27 of 142
- Download datasheet (4Mb)
3.2.2 Operating in the Power-Save Mode
VIN may be removed to allow the LP3500 to operate using the external battery once the
LP3500 is in Mode 10. At this point, the LP3500 will draw 200 µA after the subsystems
listed in Table 3 are turned off. The LP3500’s linear regulator may then be turned off using
the
The LP3500 digital I/O can continue to operate (remember that an independent +K source
is required for the digital outputs) using special software routines.
Here are some tips for when the LP3500 is in the power-save mode.
1. Do not write to the SRAM while the LP3500 is in power-save mode and you are relying
2. When the linear regulator is turned off, watch your current consumption carefully since
3.2.3 Resuming Normal-Power or Low-Power Operation
As long as VIN is still connected and the linear regulator has not been turned off, the
LP3500 will return automatically to the previous power mode once the non-zero timeout
specified in
When the timeout is set to 0, which corresponds to an indefinite timeout, the LP3500 may
still be restored to a normal power mode from the power-save mode.
1. Make sure that raw DC power is available at VIN.
2. Turn the linear regulator back on using the
3. Use the
4. Use the
User’s Manual
solely on the onboard backup battery.
too high a current draw could trigger a system reset and turn off the processor.
from VIN. Note that this function only works with LP3500 models, which have the
A/D converter.
setpowersource
NOTE: The processor will turn off if VIN is not available at the expiration of the timeout
or if VIN is not available when a wake-up signal comes in through Serial Port E or the
selected digital input.
rdPowerState
powerMode
serCommAlert
function call, and this will lower the current draw to 100 µA.
function call to set the desired power mode.
function call to establish that the LP3500 is now operating
,
timedAlert
, or
setpowersource
digInAlert
has elapsed.
function call.
21
Related parts for 101-0530
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SNGLBD BL2101 A/D 0-10V
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
CARD D/A 0-10V SR9400 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
CARD A/D 0-10V SR9300 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools WIRELESS CONTROL APP KIT
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
KIT DEV RABBITCORE RCM3750
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV RABBIT 2000 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV RABBIT RCM2000 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEVELOPMENT RCM3700 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor