AD9518-3/PCBZ Analog Devices Inc, AD9518-3/PCBZ Datasheet - Page 58
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9518-3/PCBZ
Manufacturer Part Number
AD9518-3/PCBZ
Description
BOARD EVAL FOR AD9518-3
Manufacturer
Analog Devices Inc
Specifications of AD9518-3/PCBZ
Main Purpose
Timing, Clock Generator
Utilized Ic / Part
AD9518-3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Reg.
Addr
(Hex) Bit(s) Name
190
190
191
191
191
191
191
192
192
193
193
194
194
194
194
194
195
195
AD9518-3
Table 45. LVPECL Channel Dividers
<7:4> Divider 0 Low Cycles
<3:0> Divider 0 High Cycles
<7>
<6>
<5>
<4>
<3:0> Divider 0 Phase Offset
<1>
<0>
<7:4> Divider 1 Low Cycles
<3:0> Divider 1 High Cycles
<7>
<6>
<5>
<4>
<3:0> Divider 1 Phase Offset
<1>
<0>
Divider 0 Bypass
Divider 0 Nosync
Divider 0 Force High
Divider 0 Start High
Divider 0 Direct to Output
Divider 0 DCCOFF
Divider 1 Bypass
Divider 1 Nosync
Divider 1 Force High
Divider 1 Start High
Divider 1 Direct to Output
Divider 1 DCCOFF
Description
Number of clock cycles of the divider input during which divider output stays low.
Number of clock cycles of the divider input during which divider output stays high.
Bypasses and powers down the divider; route input to divider output.
<7> = 0; use divider.
<7> = 1; bypass divider.
Nosync.
<6> = 0; obey chip-level SYNC signal.
<6> = 1; ignore chip-level SYNC signal.
Forces divider output to high. This requires that nosync also be set.
<5> = 0; divider output forced to low.
<5> = 1; divider output forced to high.
Selects clock output to start high or start low.
<4> = 0; start low.
<4> = 1; start high.
Phase offset.
Connects OUT0 and OUT1 to Divider 0 or directly to VCO or CLK.
<1> = 0; OUT0 and OUT1 are connected to Divider 0.
<1> = 1;
If 0x1E1<1:0> = 10b, the VCO is routed directly to OUT0 and OUT1.
If 0x1E1<1:0> = 00b, the CLK is routed directly to OUT0 and OUT1.
If 0x1E1<1:0> = 01b, there is no effect.
Duty-cycle correction function.
<0> = 0; enable duty-cycle correction.
<0> = 1; disable duty-cycle correction.
Number of clock cycles of the divider input during which divider output stays low.
Number of clock cycles of the divider input during which divider output stays high.
Bypasses and powers down the divider; route input to divider output.
<7> = 0; use divider.
<7> = 1; bypass divider.
Nosync.
<6> = 0; obey chip-level SYNC signal.
<6> = 1; ignore chip-level SYNC signal.
Forces divider output to high. This requires that nosync also be set.
<5> = 0; divider output forced to low.
<5> = 1; divider output forced to high.
Selects clock output to start high or start low.
<4> = 0; start low.
<4> = 1; start high.
Phase offset.
Connects OUT2 and OUT3 to Divider 1 or directly to VCO or CLK.
<1> = 0; OUT2 and OUT3 are connected to Divider 1.
<1> = 1;
If 0x1E1<1:0> = 10b, the VCO is routed directly to OUT2 and OUT3.
If 0x1E1<1:0> = 00b, the CLK is routed directly to OUT2 and OUT3.
If 0x1E1<1:0> = 01b, there is no effect.
Duty-cycle correction function.
<0> = 0; enable duty-cycle correction.
<0> = 1; disable duty-cycle correction.
Rev. 0 | Page 58 of 64