AD9518-3/PCBZ Analog Devices Inc, AD9518-3/PCBZ Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9518-3/PCBZ
Manufacturer Part Number
AD9518-3/PCBZ
Description
BOARD EVAL FOR AD9518-3
Manufacturer
Analog Devices Inc
Specifications of AD9518-3/PCBZ
Main Purpose
Timing, Clock Generator
Utilized Ic / Part
AD9518-3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9518-3
Parameter
PLL DIGITAL LOCK DETECT WINDOW
1
2
CLOCK INPUTS
Table 3.
Parameter
CLOCK INPUTS (CLK, CLK)
1
CLOCK OUTPUTS
Table 4.
Parameter
LVPECL CLOCK OUTPUTS
REFIN and REFIN self-bias points are offset slightly to avoid chatter on an open input condition.
For reliable operation of the digital lock detect, the period of the PFD frequency must be greater than the unlock-after-lock time.
Below about 1 MHz, the input should be dc-coupled. Care should be taken to match V
OUT0, OUT1, OUT2, OUT3, OUT4, OUT5
Required to Lock (Coincidence of Edges)
To Unlock After Lock (Hysteresis)
Input Frequency
Input Sensitivity, Differential
Input Common-Mode Range, V
Input Sensitivity, Single-Ended
Input Resistance
Input Capacitance
Input Level, Differential
Input Common-Mode Voltage, V
Output Frequency, Maximum
Output High Voltage (V
Output Low Voltage (V
Output Differential Voltage (V
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6 ns)
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6 ns)
OL
OH
)
)
OD
CMR
CM
2
)
2
Min
0
0
1.3
1.3
3.9
1
Min
1
Min
2950
V
V
550
S
S
− 1.12
− 2.03
Typ
150
1.57
150
4.7
2
Typ
3.5
7.5
3.5
7
15
11
Max
2.4
1.6
2
1.8
1.8
5.7
Rev. 0 | Page 6 of 64
Typ
V
V
790
S
S
Max
− 0.98
− 1.77
Unit
GHz
GHz
mV p-p
V p-p
V
V
mV p-p
kΩ
pF
CM
.
Max
980
V
V
Unit
ns
ns
ns
ns
ns
ns
S
S
− 0.84
− 1.49
Test Conditions/Comments
Differential input
High frequency distribution (VCO divider)
Distribution only (VCO divider bypassed)
Measured at 2.4 GHz; jitter performance is improved
with slew rates > 1 V/ns
Larger voltage swings may turn on the protection
diodes and can degrade jitter performance
Self-biased; enables ac coupling
With 200 mV p-p signal applied; dc-coupled
CLK ac-coupled; CLK ac-bypassed to RF ground
Self-biased
Test Conditions/Comments
Signal available at LD, STATUS, and REFMON pins
when selected by appropriate register settings
Selected by 0x17<1:0> and 0x18<4>
0x17<1:0> = 00b, 01b, 11b; 0x18<4> = 1b
0x17<1:0> = 00b, 01b, 11b; 0x18<4> = 0b
0x17<1:0> = 10b; 0x18<4> = 0b
0x17<1:0> = 00b, 01b, 11b; 0x18<4> = 1b
0x17<1:0> = 00b, 01b, 11b; 0x18<4> = 0b
0x17<1:0> = 10b; 0x18<4> = 0b
Unit
MHz
V
V
mV
Test Conditions/Comments
Termination = 50 Ω to V
Differential (OUT, OUT)
Using direct to output; see Figure 16
S
− 2 V