Y92S-38 Omron, Y92S-38 Datasheet - Page 3

• Manufacturer Part Number: Y92S-38
• Description: LOCK KEY PEN FOR H3DS RELAYS
• Manufacturer: Omron
• Series: H3DSr

Specifications of Y92S-38

• Accessory Type: Tool - Lock Key Pen
• For Use With/related Products: H3DS Series
• For Use With: H3DS-SLCAC24-230/DC24 - TIMER CAGE CLAMP 17.5MM 4MODESH3DS-MLCAC24-230/DC24-48 - TIMER CAGE CLAMP 17.5MM 8MODESZ2395 - RELAY TIME DELAY 4MODE DIN MNTZ2394 - RELAY TIME DELAY 1MODE DIN MNTZ2393 - RELAY TIME DELAY 8MODE DIN MNTZ2392 - RELAY TIME DELAY 1MODE DIN MNT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Color: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Y92S38; Z2396

H3DS
Specifications
I
Note: Can be mounted to 35-mm DIN Track with a plate thickness of 1 to 2.5 mm.
I
Note: When the time setting dial is set to “0” for any time scale, the output will operate instantaneously.
I
Note: 1. DC ripple rate: 20% max.
Item
Operating mode
Input type
Output type
External connections
Terminal block
Terminal screw tightening
torque
Mounting method
Attachment
Approved standards
Time scale display
0.1 s
1 s
0.1 m
1 m
0.1 h
1 h
10 h
Rated supply voltage
(See Notes 1 and 2.)
Operating voltage range
Power reset
Reset voltage
Power consumption (See Note 3.)
Voltage input
Control output
Ambient temperature
Ambient humidity
General
Time Ranges
Ratings
2. Since an inrush current of 0.4 A will occur when using the power supply voltage at 24 VDC, pay careful attention when turning
3. The power consumption is for mode A after the Timer counts the time-up time and for the AC input at 50 Hz. The power con-
on or off the power supply to the Timer with a solid-state output such as a sensor.
sumption of the H3DS-ML includes the input circuit with the B1 and A1 terminals short-circuited.
H3DS-ML@ @ @ @
A:
B:
B2: Repeat-cycle ON-start (Signal or Power)
C: Signal ON/OFF-delay
D: Signal OFF-delay
E:
G: Signal ON/OFF-delay
J:
Voltage input
Relay: SPDT
Screw terminal, cage clamp terminal
Screw terminal type: Clamps two 2.5-mm
Cage clamp terminal type: Clamps two 1.5-mm
0.98 N • m max.
DIN track mounting (See Note.)
Nameplate label
UL508, CSA C22.2 No.14
Conforms to EN61812-1, IEC60664-1 (VDE0110) 4 kV/2, VDE0106/P100
Output category according to IEC60947-5-1 (AC-13; 250 V 5 A/AC-14; 250 V 1 A/AC-15; 250 V 1 A/DC-13;
30 V 0.1 A/DC-14; 30 V 0.05 A)
Time range
0.1 to 1.2 s
1 to 12 s
0.1 to 1.2 min
1 to 12 min
0.1 to 1.2 h
1 to 12 h
10 to 120 h
ON-delay (Signal or Power)
Repeat-cycle OFF-start (Signal or Power)
Interval (Signal or Power)
One-shot (Signal or Power)
24 to 230 VAC (50/60 Hz)/24 to 48 VDC
85% to 110% of rated supply voltage
Minimum power-off time: 0.1 s
2.4 VAC/DC max.
AC: 32 VA max./3.0 W max. (typical: 30 VA/2.7 W) at 230 VAC
DC: 0.7 W max. (typical: 0.6 W) at 24 VDC
Max. permissible capacitance between inputs lines (terminals B1 and A2): 2,000 pF
Load connectable in parallel with inputs (terminals B1 and A1).
H-level: 20.4 to 253 VAC/20.4 to 52.8 VDC
L-level: 0 to 2.4 VAC/DC
Contact output: 5 A at 250 VAC with resistive load (cos φ = 1); 5 A at 30 VDC with resistive
load (cos φ = 1)
Operating: –10 ° C to 55 ° C (14 ° F to 131 ° F) with no icing
Storage: –25 ° C to 65 ° C (-13 ° F to 149 ° F) with no icing
Operating: 35% to 85%
14 VA max./2.2 W max. (typical: 13 VA/2.1 W) at 100 to 120 VAC
1.4 W max. (typical: 1.3 W) at 48 VDC
2
max. bar terminals without sleeves.
2
max. bar terminals without sleeves.
H3DS-SL@ @ @ @
A: ON-delay
B2: Repeat-cycle ON-start
E: Interval
J:
---
One-shot
H3DS-AL@ @ @ @
A: ON-delay (fixed)
H3DS