P2CF-11-E Omron, P2CF-11-E Datasheet - Page 68

• Manufacturer Part Number: P2CF-11-E
• Description: SOCKET 11-PIN FOR H3CR-H
• Manufacturer: Omron
• Type: Socketr
• Series: -r

Specifications of P2CF-11-E

• Number Of Positions: 11
• Mounting Type: DIN Rail
• Termination Style: Screw Terminal
• Features: -
• Socket Mounting: DIN Rail
• Socket Terminals: Screw
• Voltage Rating: 240VAC
• No. Of Pins: 11
• Accessory Type: Finger Safe Terminal
• Rohs Compliant: Yes
• For Use With/related Products: Multiple Series
• For Use With: Z2998 - RELAY TIMER DGTL SPDT 100/240VACZ2366 - RELAY REPEAT CYCLE ANLG 30HRSZ997 - RELAY TIMER ANALOG 24VDC/ACZ2358 - RELAY REPEAT CYCLE ANLG 30HRSZ876 - RELAY TIMER DPDT ANALOG 120\240V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: P2CF11E

68
E5@N/E5@N-H
Mounting
Mounting to a Panel
For waterproof mounting, waterproof packing must be installed on the
Controller. Waterproofing is not possible when group mounting
several Controllers. Waterproof packing is not necessary when there
is no need for the waterproofing function.
E5CN
1. The Panel Mounting Adapter is also included with the E5CN-U.
2. Insert the E5CN/E5CN-U into the mounting hole in the panel.
3. Push the adapter from the terminals up to the panel, and
4. Tighten the two fastening screws on the adapter. Alternately
E5EN/E5AN
1. Insert the E5AN/E5EN into the square mounting hole in the panel
2. Use a ratchet to alternately tighten the screws on the top and
E53-COV17
Terminal Cover
(Accessory)
There is no waterproof packing included with the E5CN-U.
temporarily fasten the E5CN/E5CN-U.
tighten the two screws little by little to maintain a balance. Tighten
the screws to a torque of 0.29 to 0.39 N·m.
(thickness: 1 to 8 mm). Attach the Mounting Brackets provided with
the product to the mounting grooves on the top and bottom
surfaces of the rear case.
bottom Mounting Brackets little by little to maintain balance, until
the ratchet turns freely.
Waterproof packing
(Accessory)
E53-COV16
Terminal Cover
(Accessory)
E53-COV16
Terminal Cover
(Accessory)
Adapter
(Accessory)
Panel
E5CN
Mounting Bracket
(Accessory)
Mounting Bracket
(Accessory)
Waterproof
packing
(Accessory)
Waterproof
packing
(Accessory)
Order the P2CF-11 or
P3GA-11 Socket separately.
Panel
E5AN
E5EN
For Front-mounting Socket
(Panel mounting is also possible.)
Panel
E5CN-U
Mounting the Terminal Cover
E5CN
Make sure that the “UP” mark is facing up, and then attach the E53-
COV17 Terminal Cover to the holes on the top and bottom of the
Temperature Controller.
E5AN/E5EN
Slightly bend the E53-COV16 Terminal Cover to attach it to the
terminal block as shown in the following diagram. The Terminal Cover
cannot be attached in the opposite direction.
Removing the Temperature Controller from the
Case
The Temperature Controller can be removed from the case to perform
maintenance without removing the terminal leads. This is possible for
only the E5CN, E5AN, and E5EN, and not for the E5CN-U. Check the
specifications of the case and Temperature Controller before
removing the Temperature Controller from the case.
E5CN
1. Insert a flat-blade screwdriver into the two tool insertion holes (one
2. Insert the flat-blade screwdriver in the gap between the front panel
3. When inserting the body of the Temperature Controller into the
on the top and one on the bottom) to release the hooks.
and rear case, and pull out the front panel slightly. Hold the top and
bottom of the front panel and carefully pull it out toward you,
without applying unnecessary force.
case, make sure the PCBs are parallel to each other, make sure
that the sealing rubber is in place, and press the E5CN toward the
rear case into position. While pushing the E5CN into place, push
down on the hooks on the top and bottom surfaces of the rear case
so that the hooks are securely locked in place. Be sure that
electronic components do not come into contact with the case.
Tool insertion hole
E53-COV16
Terminal Cover
(Accessory)
(1)
(1)
(2)
(3)
Slightly bend the
E53-COV16
Terminal Cover in
the direction shown
by the arrows to
attach it to the
terminal block.
Flat-blade screwdriver
(Unit: mm)
0.4
2.0