PIC16F690-I/SO Microchip Technology, PIC16F690-I/SO Datasheet - Page 145

• Manufacturer Part Number: PIC16F690-I/SO
• Description: IC PIC MCU FLASH 4KX14 20SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F690-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 20-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SPI/SSP/EUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-1, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Data Rom Size: 256 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 2.31 mm
• Length: 12.8 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Width: 7.49 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SO1-1 - SOCKET TRANS ICE 20DIP TO 20SOICPIC16F690DM-PCTLHS - BOARD DEMO PICTAIL HUMIDITY SNSRAC162061 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

11.4.6
In Half-Bridge applications where all power switches
are modulated at the PWM frequency, the power
switches normally require more time to turn off than to
turn on. If both the upper and lower power switches are
switched at the same time (one turned on, and the
other turned off), both switches may be on for a short
period of time until one switch completely turns off.
During this brief interval, a very high current
(shoot-through current) will flow through both power
switches, shorting the bridge supply. To avoid this
potentially destructive shoot-through current from
flowing during switching, turning on either of the power
switches is normally delayed to allow the other switch
to completely turn off.
In Half-Bridge mode, a digitally programmable
dead-band delay is available to avoid shoot-through
current from destroying the bridge power switches. The
delay occurs at the signal transition from the non-active
state to the active state. See Figure 11-8 for illustration.
The lower seven bits of the associated PWM1CON
register (Register 11-3) sets the delay period in terms
of microcontroller instruction cycles (T
FIGURE 11-17:
© 2006 Microchip Technology Inc.
Standard Half-Bridge Circuit (“Push-Pull”)
PROGRAMMABLE DEAD-BAND
DELAY MODE
EXAMPLE OF HALF-BRIDGE APPLICATIONS
PIC16F631/677/685/687/689/690
CY
or 4 T
P1A
P1B
OSC
).
Preliminary
FET
Driver
FET
Driver
FIGURE 11-16:
P1A
P1B
td = Dead-Band Delay
Note 1: At this time, the TMR2 register is equal to the
(2)
(2)
V+
V-
2: Output signals are shown as active-high.
(1)
td
Pulse Width
PR2 register.
Load
Period
td
EXAMPLE OF
HALF-BRIDGE PWM
OUTPUT
+
V
-
+
V
-
(1)
DS41262C-page 143
Period
(1)