PIC16F690-I/SO Microchip Technology, PIC16F690-I/SO Datasheet - Page 207

• Manufacturer Part Number: PIC16F690-I/SO
• Description: IC PIC MCU FLASH 4KX14 20SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F690-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 20-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SPI/SSP/EUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-1, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Data Rom Size: 256 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 2.31 mm
• Length: 12.8 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Width: 7.49 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SO1-1 - SOCKET TRANS ICE 20DIP TO 20SOICPIC16F690DM-PCTLHS - BOARD DEMO PICTAIL HUMIDITY SNSRAC162061 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

14.3.2
An overflow (FFh
the T0IF (INTCON<2>) bit. The interrupt can be
enabled/disabled by setting/clearing T0IE (INTCON<5>)
bit. See Section 5.0 “Timer0 Module” for operation of
the Timer0 module.
FIGURE 14-7:
© 2006 Microchip Technology Inc.
IOC-RA0
IOC-RA1
IOC-RA2
IOC-RA3
IOC-RA4
IOC-RA5
IOC-RB4
IOC-RB5
IOC-RB6
IOC-RB7
IOCA0
IOCA1
IOCA2
IOCA3
IOCA4
IOCA5
IOCB4
IOCB5
IOCB6
IOCB7
TMR0 INTERRUPT
00h) in the TMR0 register will set
INTERRUPT LOGIC
PIC16F631/677/685/687/689/690
TMR2IE
TMR1IF
TMR1IE
TMR2IF
CCP1IF
CCP1IE
OSFIF
OSFIE
SSPIF
SSPIE
RCIE
RCIF
ADIF
ADIE
TXIF
TXIE
C1IF
C1IE
C2IF
C2IE
EEIF
EEIE
Preliminary
14.3.3
An input change on PORTA or PORTB change sets the
RABIF (INTCON<0>) bit. The interrupt can be enabled/
disabled by setting/clearing the RABIE (INTCON<3>)
bit. Plus, individual pins can be configured through the
IOCA or IOCB registers.
Note 1:
Note:
RABIE
RABIF
INTF
INTE
PEIE
T0IF
T0IE
GIE
PORTA/PORTB INTERRUPT
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RABIF
interrupt flag may not get set. See
Section 4.2.3 “Interrupt-on-change” for
more information.
Some peripherals depend upon the system
clock for operation. Since the system clock is
suspended during Sleep, these peripherals
will not wake the part from Sleep. See
Section 14.6.1 “Wake-up from Sleep”.
Wake-up (If in Sleep mode)
DS41262C-page 205
Interrupt to CPU
(1)