PIC16F690-I/SO Microchip Technology, PIC16F690-I/SO Datasheet - Page 169

• Manufacturer Part Number: PIC16F690-I/SO
• Description: IC PIC MCU FLASH 4KX14 20SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F690-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 20-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SPI/SSP/EUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-1, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Data Rom Size: 256 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 2.31 mm
• Length: 12.8 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Width: 7.49 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SO1-1 - SOCKET TRANS ICE 20DIP TO 20SOICPIC16F690DM-PCTLHS - BOARD DEMO PICTAIL HUMIDITY SNSRAC162061 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 12-8:
12.3.3
The EUSART module has the capability of sending the
special Break character sequences that are required by
the LIN bus standard. A Break character consists of a
Start bit, followed by 12 ‘0’ bits and a Stop bit.
To send a Break character, set the SENDB and TXEN
bits of the TXSTA register. The Break character trans-
mission is then initiated by a write to the TXREG. The
value of data written to TXREG will be ignored and all
‘0’s will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN specification).
The TRMT bit of the TXSTA register indicates when the
transmit operation is active or Idle, just as it does during
normal transmission. See Figure 12-9 for the timing of
the Break character sequence.
12.3.3.1
The following sequence will start a message frame
header made up of a Break, followed by an auto-baud
Sync byte. This sequence is typical of a LIN bus
master.
1.
2.
3.
4.
5.
When the TXREG becomes empty, as indicated by the
TXIF, the next data byte can be written to TXREG.
© 2006 Microchip Technology Inc.
RX/DT Line
Note 1:
WUE bit
Configure the EUSART for the desired mode.
Set the TXEN and SENDB bits to enable the
Break sequence.
Load the TXREG with a dummy character to
initiate transmission (the value is ignored).
Write ‘55h’ to TXREG to load the Sync character
into the transmit FIFO buffer.
After the Break has been sent, the SENDB bit is
reset by hardware and the Sync character is
then transmitted.
OSC1
RCIF
2:
If the wake-up event requires long oscillator warm-up time, the automatic clearing of the WUE bit can occur while the stposc signal is
still active. This sequence should not depend on the presence of Q clocks.
The EUSART remains in Idle while the WUE bit is set.
Q1Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1Q2 Q3 Q4
BREAK CHARACTER SEQUENCE
Bit Set by User
Break and Sync Transmit Sequence
Sleep Command Executed
AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP
PIC16F631/677/685/687/689/690
Q1
Preliminary
Sleep Ends
12.3.4
The Enhanced EUSART module can receive a Break
character in two ways.
The first method to detect a Break character uses the
FERR bit of the RCSTA register and the Received data
as indicated by RCREG. The Baud Rate Generator is
assumed to have been initialized to the expected baud
rate.
A Break character has been received when;
• RCIF bit is set
• FERR bit is set
• RCREG = 00h
The second method uses the Auto-Wake-up feature
described in Section 12.3.2 “Auto-Wake-up on
Break”. By enabling this feature, the EUSART will
sample the next two transitions on RX/DT, cause an
RCIF interrupt, and receive the next data byte followed
by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Detect feature.
For both methods, the user can set the ABDEN bit of
the BAUDCTL register before placing the EUSART in
Sleep mode.
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4
Cleared due to User Read of RCREG
RECEIVING A BREAK CHARACTER
Note 1
DS41262C-page 167
Auto Cleared